background image

45

EN

31. Oktober 2016

14:22:38

3

Control panel - graphic user interface

Extended Settings (submenu)

13. Operation

Heating

Touch the 

 icon for 3 sec. to turn the heating on. The control unit with switch on the steam 

generator and load the pre-set settings (temperature, time, etc.). To switch off briefly touch this 

symbol again.

Light

To turn the cabin light on or off, briefly touch the lamp on the display panel.

Private use:

Touch briefly the symbol 

 to launch extended settings. A submenu will open as shown below. 

In this menu you can set all common settings which are not required frequently.

Commercial use:

By commercial use touch the symbol 

 for 3 sec. and give in the access code 

5645

. Extended settings will be opened 

in a new window. A short touch on the 
symbol 

 will open a submenu for nav-

igation language selection only. The full 

set of extended settings is only accessible 

with the given above code.

Pic. 2

!

31. Oktober 2016

14:22:38

Einstellungen

Settings

Climate query

Cabin light

Coloured light

  

(optional)

Temperature / Essence dosing

Press >3 sec to set temperature and 

control essence dosing

Date & time

Fault

Settings

Cabin selection by 
multiple cabins

On / Off

touch >3 sec to 

switch on

Info messages and warnings

Summary of Contents for SteamRock Premium





































































Reviews: