Endress+Hauser Micropilot S FMR531 Operating Instructions Manual Download Page 33

Page: 33 / 100

Micropilot S FMR531 with HART/4...20 mA

Operation

E Hauser

5.2.2

Display symbols

The following table describes the symbols that appear on the liquid crystal display:

Light emitting diods (LEDs):

There is a green and a red LED besides the Liquid Crystal Display.

Symbols

Meaning

ALARM_SYMBOL

This alarm symbol appears when the instrument is in an alarm state. If the symbol flashes, this indicates a
warning.

LOCK_SYMBOL

This lock symbol appears when the instrument is locked,i.e. if no input is possible.

COM_SYMBOL

This communication symbol appears when a data transmission via e.g. HART is in progress.

Calibration to regulatory standards disturbed

If the instrument is not locked or it cannot guarantee the calibration to regulatory standards, the situation
will be indicated on the display via the symbol.

LED (LED)

Meaning

red LED continuously on

Alarm

red LED flashes

Warning

red LED off

No alarm

green LED continuously on

Operation

Green LED flashes

Communication with external device

Summary of Contents for Micropilot S FMR531





































































































Search results

Summary of Contents for Micropilot S FMR531

Reviews:

Related manuals for Micropilot S FMR531

Brands by name

Popular brands

Endress+Hauser Micropilot S FMR531, Operating Instructions Manual

Search results

Summary of Contents for Micropilot S FMR531

Reviews:

Related manuals for Micropilot S FMR531

Brands by name

Popular brands