Endress+Hauser Micropilot S FMR531 Operating Instructions Manual Download Page 74

Page: 74 / 100

Trouble-shooting

Micropilot S FMR531 with HART/4...20 mA

E Hauser

Error

Output

Possible cause

Remedy

If the surface is not
calm (e.g. filling,
emptying, agitator
running), the
measured value
jumps sporadically
to a higher level

L00-FMR53xxx-19-00-00-en-008

Signal is weakened by
the rough surface — the
interference echoes
are sometimes stronger

Carry out tank mapping

→

basic

setup

Set the process cond. (004) to
"turb. surface" or "agitator

Increase the output damping
(058)

Optimise the orientation
(see Page 75)

If necessary, select a better
mounting position and/or larger
antenna (see Page 15)

During filling/
emptying the
measured value
jumps sporadically
to a higher/lower
level

L00-FMR53xxx-19-00-00-en-009

During definition of the
auto correction table
the instrument has been
switched off and the
level has changed.

Reset "555"

Iff possible, do not switch off the
instrument before the complete
measuring range has been passed
through.

During filling/
emptying the
measured value
jumps downwards

L00-FMR53xxx-19-00-00-en-004

Multiple echoes

yes

→

Check the tank shape (002),
e.g. "dome ceiling" or
"horizontal cyl"

In the range of the blocking dist.
(059) there is no echo evaluation

→

Adapt the value

If possible, do not select
central installation position
(see Page 15)

Activate auto correktion (031)

E 641 ((loss
ofecho)

L00-FMR53xxx-19-00-00-en-005

Level echo is tooweak.

Possible causes:
• Rough surface dueto

filling/emptying

• Agitator running
• Foam

yes

→

Check application parameters
(002), (003) and (004)

Optimise alignment
(see Page 75)

If necessary, select a better
installation position and/or larger
antenna (see Page 15)

E 641 (loss ofecho)
after turn onthe
power supply

If the instrument is configured to Hold by lossof
echo the output is set to anyvalue/current.

noise level during
theinitialisation phase
tohigh.

Repeat once more empty calibr.
(005).

Caution!
Before conformation change with

to the edit mode.

20 mA/100%

4 mA/0%

→

actual

expected

20 mA/100%

4 mA/0%

→

expected

actual

20 mA/100%

4 mA/0%

→

expected

actual

20 mA/100%

E 641

4 mA/0%

→

actual

expected

Summary of Contents for Micropilot S FMR531





































































































Search results

Summary of Contents for Micropilot S FMR531

Reviews:

Related manuals for Micropilot S FMR531

Brands by name

Popular brands

Endress+Hauser Micropilot S FMR531, Operating Instructions Manual

Search results

Summary of Contents for Micropilot S FMR531

Reviews:

Related manuals for Micropilot S FMR531

Brands by name

Popular brands