Emtek R100 User Manual Download | Manualshive

Page: 73 / 73

background image

EMTEK, LLC - R100 USERS MANUAL / AUG2019.REV01

73

Appendix F: Packaging Components and Packaging (continued)

Packaging Insructions:

1)

Place R100 and RAS Air Sampler Components in the Component Tray, and tubing in the Spacer pocket,
as shown on the previous page.

2)

Assemble the packaging contents as shown below, and described in steps A-D

A) Place Component Tray Cover on Component Tray and set Carboard Spacer on top of Component tray
B) Lay the outer shipping box flat on its’ side, and slide the Component Tray and Spacer into the box.

C) Stand box up and asssure the Component Tray and Cardboard Spacer are fully pushed into the box
D) Fold the outer box flaps closed and tape the shipping box securely closed.

«
...
71
72
73

Summary of Contents for R100










































































Reviews:

No comments

Related manuals for R100

Brand: Califone Pages: 7

Brand: CALITEK Pages: 16

Brand: LAHTI PRO Pages: 20

Brand: LAHTI PRO Pages: 16

Brand: J&M Pages: 53

Brand: Qazqa Pages: 2

Brand: CAMAG Pages: 40

Brand: e-survey Pages: 54

Brand: E-Pill Pages: 8

XL-7 Command Station

Brand: E-Mu Pages: 22

Brand: EASTERN INSTRUMENTS Pages: 93

Brand: EarthQuake Pages: 12

Brand: Pari Pages: 2

Brand: Gearmore Pages: 47

Brand: Xtool Pages: 51

Brand: H-TEC Education Pages: 16

Brand: H-TEC Education Pages: 12

Brand: Pari Pages: 12

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands