Emtek R100 User Manual Download Page 55 | Manualshive

Page: 55 / 73

background image

EMTEK, LLC - R100 USERS MANUAL / AUG2019.REV01

55

1.2.2

For sampling at 100 LPM, the tubing length may be up to 10 Feet (3 Meters).

1.2.2.1

Tubing  used  between  the  R100  and  RAS  must  have  a  0.500”  ID,  as  supplied  by
EMTEK.    Smaller ID tubing will be too restrictive to achieve the desired flow rate at
the RAS.

1.3

Connect the tubing to the R100 and the RAS using the supplied sanitary connector fittings, seals, and
clamps, as shown in the following examples for flexible tubing (Fig 1) and rigid tubing (Fig ).

Fig 1 - FLEXIBLE TUBING (RAS Side Connection Port Used)

«
...
53
54
55
56
57
...
»

Summary of Contents for R100










































































Reviews:

No comments

Related manuals for R100

Brand: Raith Pages: 26

Brand: Kane Pages: 16

Brand: Abus Pages: 2

Brand: Abus Pages: 12

Brand: Abu Garcia Pages: 6

Brand: Above All Pages: 4

Brand: Cannon Pages: 40

Brand: NARGESA Pages: 34

Brand: Land Pride Pages: 36

Skid Steer Rakes SR2672

Brand: Land Pride Pages: 2

Brand: Land Pride Pages: 2

Disc Harrows DH3510

Brand: Land Pride Pages: 2

Brand: Land Pride Pages: 4

Brand: Land Pride Pages: 4

Straw Crimper CR2572

Brand: Land Pride Pages: 16

Brand: Oakworks Medical Pages: 28

Brand: Latham Pages: 4

Brand: SafeWaze Pages: 23

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands