Emerson Rosemount X-STREAM O2 Transmitter Instruction Manual Download Page 61 | Manualshive

Page: 61 / 174

background image

Instruction Manual

IM-106-910C, Rev. 1.0

November 2009

3-3

Hazardous Area

X-STREAM O

2

Transmitter

Set Test Gas Values Using Xi Enhanced Interface Keypad/Display

1. Press the MENU button once.
2. From the main menu, select PROBE 1.
3. From PROBE 1, select DETAILED SETUP.
4. From the DETAILED SETUP menu, select CAL SETUP.
5. From CAL SETUP, select Cal Gas 1. Enter the percent O2 used for the

low O2 test gas.

6. From CAL SETUP, select Cal Gas 2. Enter the percent O2 used for the

high O2 test gas.

7. Press the LEFT arrow key several times to return to the main menu.
8. Repeat steps 2 through 6 for PROBE 2 if configured for dual channel.

ALARM RELAY OUTPUT
CONFIGURATION

The Xi Enhanced Interface has two dry contact Form-C alarm relay output

signals that can be configured in eight different modes through the Xi keypad

display or the 375 Communicator. A list of possible configurations is shown in

Table 3-1. Each alarm relay output can be configured separately.
If the Xi Enhanced Interface is configured with the optional Flame Safety

Interlock, Alarm 2 is configured with "Heater Relay" and prewired to the AC

Relay Board. In this condition, the relay configuration cannot be changed to

any other setting. If the Xi Enhanced Interface is not configured with the

optional Flame Safety Interlock, "Heater Relay" is not valid and cannot be

chosen for Alarm 2.

Table 3-1. Alarm Relay Output

Configurations

Configuring Alarm Relays with the Field Communicator

1. Use the 375 Field Communicator software to access the HART menu.
2. From the DEVICE SETUP menu, select DETAILED SETUP.
3. From the DETAILED SETUP menu, select ALARM RELAY.

Mode

Configuration

No Alarm*

The output is not configured for any alarm condition.

Unit Alarm

The output is configured for a Unit Alarm.

Low O

2

Alarm

The output is configured for a Low O

2

alarm.

Low O

2

/Unit Alm

The output is configured for a Unit alarm and a Low O

2

alarm.

Cal Recommended

The output is configured for a Calibration Recommended
display.

Cal Rec/Unit Alm**

The output is configured for a Unit alarm and a Calibration
Recommended display.

Low O

2

/Cal Rec

The output is configured for a Low O

2

alarm and a Calibration

Recommended display.

Low O

2

/Unit/Cal Rec

The output is configured for a Low O

2

alarm, a Unit alarm, and a

Calibration Recommended display.

Heater Relay

The output is configured for Flame Safety Interlock.

* The default configuration for Alarm 2

** The default configuration for Alarm 1

«
...
59
60
61
62
63
...
»

Summary of Contents for Rosemount X-STREAM O2 Transmitter















































































































































































Reviews:

No comments

Related manuals for Rosemount X-STREAM O2 Transmitter

Brand: Campbell Pages: 52

Brand: Campbell Pages: 34

Brand: Nautel Pages: 20

Brand: Nautel Pages: 109

Brand: Harris Pages: 162

Brand: MuxLab Pages: 2

Brand: Labom Pages: 3

Brand: Audio Precision Pages: 44

Brand: CHUNDE TECHNOLOGY Pages: 2

Brand: HBC Pages: 18

PULSAR RADAR R86

Brand: Magnetrol Pages: 16

PluraSens E2648-NH3-E

Brand: Evikon Pages: 21

Brand: F&F Pages: 12

Brand: Humminbird Pages: 2

Brand: Midland Pages: 85

Brand: SGM LEKTRA Pages: 40

Brand: SG Security Communications Pages: 24

833-II-(Axxx)-(Axxx) series

Brand: F.u.n.k.e. Pages: 56

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands