Emerson Rosemount X-STREAM O2 Transmitter Instruction Manual Download Page 24

Page: 24 / 174

Hazardous Area

X-STREAM O

Transmitter

1-8

Instruction Manual

IM-106-910C, Rev. 1.0

November 2009

NOTES:

The 375 Field Communicator must be upgraded to System Software 2.0 with

Graphic License for operation with the Hazardous Area X-STREAM O

Transmitter. The AMS software must be upgraded to AMS 8.0 or above.

Contact Emerson Process Management’s Global Service Center (GSC) at

1-800-833-8314 to upgrade the 375 Field Communicator software to System

Software 2.0 with Graphic License.

Optional OxyBalance Display and Averaging System

Receives up to eight 4-20 mA signals from individual probes. Trends

individual outputs and calculates four programmable averages as additional

4-20 mA outputs. OxyBalance graphic displays are shown in Figure 1-6. See

IM-106-4050, OxyBalance Oxygen Display and Averaging System, for

additional details.

Figure 1-6. OxyBalance

Displays

38890063

Analytical

Summary of Contents for Rosemount X-STREAM O2 Transmitter















































































































































































Search results

Summary of Contents for Rosemount X-STREAM O2 Transmitter

Reviews:

Related manuals for Rosemount X-STREAM O2 Transmitter

Brands by name

Popular brands

Emerson Rosemount X-STREAM O2 Transmitter, Instruction Manual

Search results

Summary of Contents for Rosemount X-STREAM O2 Transmitter

Reviews:

Related manuals for Rosemount X-STREAM O2 Transmitter

Brands by name

Popular brands