Emerson Rosemount X-STREAM O2 Transmitter Instruction Manual Download Page 115

Page: 115 / 174

Instruction Manual

IM-106-910C, Rev. 1.0

November 2009

6-17

Hazardous Area

X-STREAM O

Transmitter

Replacing Right Housing Cover

1. See Figure 6-1. Loosen and remove the lock clip (22) from the cover

lock slots.

2. Remove existing housing cover (12, Figure 6-1) from the right hand side

of the probe housing.

NOTE

A field wiring label is required for the inside surface of the right housing cover.

3. Select the new field wiring label (10) that matches the existing label on

the inside of the old cover.

4. Peel off the backing from the field wiring label and attach the new label

to the inside of the new cover. The graphic image that appears on this

label is shown in Figure 6-13.

5. Install the new housing cover (12, Figure 6-1) onto the probe housing.
6. Insert the lock clip (22) into the cover lock slots and tighten screw (24).

Figure 6-13. Field Wiring Label

Summary of Contents for Rosemount X-STREAM O2 Transmitter















































































































































































Search results

Summary of Contents for Rosemount X-STREAM O2 Transmitter

Reviews:

Related manuals for Rosemount X-STREAM O2 Transmitter

Brands by name

Popular brands

Emerson Rosemount X-STREAM O2 Transmitter, Instruction Manual

Search results

Summary of Contents for Rosemount X-STREAM O2 Transmitter

Reviews:

Related manuals for Rosemount X-STREAM O2 Transmitter

Brands by name

Popular brands