Emerson Bettis 500 Installation And Operation Manual Download

Page: 84 / 102

February 2018

Installation and Operation Manual

E2K-405-0218 Rev. 2

Section 6: Troubleshooting

Troubleshooting

6.2.3 Display Torque Archive

Torque archive is displayed like Torque Profile. Torque archive is the data stored at
the time commanded by the user in the “

CHANGE SETTINGS

” mode. See

Section

5.5.2, Valve Control Setup

and

Figure 5-6

At the “

DISPLAY TORQUE ARCHIVE?

” prompt, answer “

YES.

”

See

Section 6.2.2

Display Torque Profile

, and

Figure 6-3

6.2.4 Display Operation Log

Operation log aids in troubleshooting because it contains the operation data
accumulated since the operation log was reset. See

Figure 6-4

At the “

DISPLAY OPERATE LOG?

” prompt, answer “

YES.

”

Use the control knob

(YES)

to review the operate log.

Motor starts value is the number of times the motor has been started. The strokes
value displayed is the number of full strokes from limit to limit. Stroke time can be
measured as follows:

Reset operation log.

Stroke the valve. Stroke time is equal to the motor run time.

Motor run time is the total motor operational time.

To reset operation log:

Enter “

Change Settings

” mode.

Select “

VALVE CONTROL SETUP?

”

See

Section 5.5.2, Valve Control Setup

Figure 6-4

Display Operation Log

YES

Analog

<analog_state>

<state: NORMAL/

NOT CONFIGURED/

UNDER RANGE/

OVER RANGE>

Network

<network_state>

<state: NORMAL/

NOT CONFIGURED/

SPI LINK LOST/ACM

FAILED/HOST LOST

EFM

<efm_state>

<state: NORMAL/

SHUTDOWN/

FAILED>

Refresh every

30 seconds

BACK

YES

DISPLAY

ALARM LOG?

DISPLAY ALARM LOG

Figure 6-2

Go to

Figure 6-1

DISPLAY TORQUE PROFILE

Figure 6-3

NO
OR

NEXT

NO
OR

NEXT

BACK

NEXT

YES

1 <alarm 1>
2 <alarm 2>

YES

DISPLAY

TORQUE PROFILE

Pull-out

Torque

<xx>%

YES

3 <alarm 3>
4 <alarm 4>

YES

5 <alarm 5>
6 <alarm 6>

YES

7 <alarm 7>
8 <alarm 8>

YES

9 <alarm 9>

10 <alarm 10>

YES

DISPLAY

OPERATE LOG?

DISPLAY OPERATION LOG

Figure 6-4

DISPLAY HARDWARE

Figure 6-6

NO
OR

NEXT

BACK

NEXT

YES

Motor
Starts

<xxx,xxx,xxx>

YES

BACK

NEXT

YES

@10 Torque =

<xx>%

@20 Torque =

<xx>%

Display Open

Torque

Profile?

YES

@30 Torque =

<xx>%

@40 Torque =

<xx>%

@50 Torque =

<xx>%

@60 Torque =

<xx>%

@70 Torque =

<xx>%

@80 Torque =

<xx>%

@90 Torque =

<xx>%

YES

@10 Torque =

<xx>%

@20 Torque =

<xx>%

Display Close

Torque

Profile?

YES

@30 Torque =

<xx>%

@40 Torque =

<xx>%

@50 Torque =

<xx>%

@60 Torque =

<xx>%

@70 Torque =

<xx>%

@80 Torque =

<xx>%

@90 Torque =

<xx>%

NO
OR

NEXT

YES

Pull-out

Torque

<xx>%

YES

BACK

NEXT

YES

@10 Torque =

<xx>%

@20 Torque =

<xx>%

Display Open

Torque

Archive?

YES

@30 Torque =

<xx>%

@40 Torque =

<xx>%

@50 Torque =

<xx>%

@60 Torque =

<xx>%

@70 Torque =

<xx>%

@80 Torque =

<xx>%

@90 Torque =

<xx>%

YES

@10 Torque =

<xx>%

@20 Torque =

<xx>%

Display Close

Torque

Archive?

YES

@30 Torque =

<xx>%

@40 Torque =

<xx>%

@50 Torque =

<xx>%

@60 Torque =

<xx>%

@70 Torque =

<xx>%

@80 Torque =

<xx>%

@90 Torque =

<xx>%

DISPLAY

TORQUE ARCHIVE

NO
OR

NEXT

YES

REMOTE

DISPLAY#2

<rem_disp#2_state>

<state: NORMAL/

NOT CONFIGURED/

LOST LINK/FAILED>

YES

BACK

NEXT

YES

APD Module

<apd_state>

<state: NORMAL/

FAILED>

Inside

Temperature=

<xx>C

YES

DISPLAY

HARDWARE?

EXIT?

Strokes

<xxx,xxx,xxx>

Motor

Run Time

<hr:min:sec>

YES

DISPLAY

OPERATE ARCHIVE?

DISPLAY OPERATION ARCHIVE

Figure 6-5

NO
OR

NEXT

BACK

NEXT

YES

Motor
Starts

<xxx,xxx,xxx>

YES

Strokes

<xxx,xxx,xxx>

Motor

Run Time
<hours>

Central Control

<cen_ctrl_state>

<state: NORMAL/

LOST LINK /FAILED>

Local Display

<lcl_disp_state>

<state: NORMAL/

LOST LINK /FAILED>

REMOTE

DISPLAY#1

<rem_disp#1_state>

<state: NORMAL/

NOT CONFIGURED/

LOST LINK / FAILED>

Summary of Contents for Bettis 500







































































































Search results

Summary of Contents for Bettis 500

Reviews:

Related manuals for Bettis 500

Brands by name

Popular brands

Emerson Bettis 500, Installation And Operation Manual

Search results

Summary of Contents for Bettis 500

Reviews:

Related manuals for Bettis 500

Brands by name

Popular brands