Emerson Bettis 500 Installation And Operation Manual Download Page 82

Page: 82 / 102

February 2018

Installation and Operation Manual

E2K-405-0218 Rev. 2

Section 6: Troubleshooting

Troubleshooting

6.2.1 Display Alarm Log

At the time the alarm occurs, the alarm is displayed on the bottom line of the
message center. This display lists the last nine alarms that have occurred. The first
alarm listed is the most recent to occur. The alarm list progresses from the most
recent to the oldest. The following alarms may be displayed.

EFM MONITOR

OPEN INHIBIT

OPEN TORQUE_%

CLOSE INHIBIT

CLOSE TORQUE_%

LOCAL ESD

VALVE STALLED

REMOTE ESD

VALVE DRIFT

LOST AIN1 SIGNAL

POWER FAIL

ACTUATOR FAIL

LOST PHASE

SETUP ERROR

MOTOR OVERLOAD

SET LIMITS BEFORE OPERATING

NOTE:

When the “

SET LIMITS BEFORE OPERATING

” alarm is displayed, no other alarms

will be displayed until the limits are set.

At the “

DISPLAY ALARM LOG?

” prompt, answer “

YES.

”

Use the selector knob (

NEXT/BACK

) to review the alarms. See

Figure 6-2

NOTE:

The control knob (

YES/NO

) can be used to view the alarms however do

not cycle the control knob between

and

YES

because the unit could

display the “

SETUP

” mode.

Use the control knob

(NO)

to exit the display.

Figure 6-2

Display Alarm Log Example

YES

Analog

<analog_state>

<state: NORMAL/

NOT CONFIGURED/

UNDER RANGE/

OVER RANGE>

Network

<network_state>

<state: NORMAL/

NOT CONFIGURED/

SPI LINK LOST/ACM

FAILED/HOST LOST

EFM

<efm_state>

<state: NORMAL/

SHUTDOWN/

FAILED>

Refresh every

30 seconds

BACK

YES

DISPLAY

ALARM LOG?

DISPLAY ALARM LOG

Figure 6-2

Go to

Figure 6-1

DISPLAY TORQUE PROFILE

Figure 6-3

NO
OR

NEXT

NO
OR

NEXT

BACK

NEXT

YES

1 <alarm 1>
2 <alarm 2>

YES

DISPLAY

TORQUE PROFILE

Pull-out

Torque

<xx>%

YES

3 <alarm 3>
4 <alarm 4>

YES

5 <alarm 5>
6 <alarm 6>

YES

7 <alarm 7>
8 <alarm 8>

YES

9 <alarm 9>

10 <alarm 10>

YES

DISPLAY

OPERATE LOG?

DISPLAY OPERATION LOG

Figure 6-4

DISPLAY HARDWARE

Figure 6-6

NO
OR

NEXT

BACK

NEXT

YES

Motor
Starts

<xxx,xxx,xxx>

YES

BACK

NEXT

YES

@10 Torque =

<xx>%

@20 Torque =

<xx>%

Display Open

Torque

Profile?

YES

@30 Torque =

<xx>%

@40 Torque =

<xx>%

@50 Torque =

<xx>%

@60 Torque =

<xx>%

@70 Torque =

<xx>%

@80 Torque =

<xx>%

@90 Torque =

<xx>%

YES

@10 Torque =

<xx>%

@20 Torque =

<xx>%

Display Close

Torque

Profile?

YES

@30 Torque =

<xx>%

@40 Torque =

<xx>%

@50 Torque =

<xx>%

@60 Torque =

<xx>%

@70 Torque =

<xx>%

@80 Torque =

<xx>%

@90 Torque =

<xx>%

NO
OR

NEXT

YES

Pull-out

Torque

<xx>%

YES

BACK

NEXT

YES

@10 Torque =

<xx>%

@20 Torque =

<xx>%

Display Open

Torque

Archive?

YES

@30 Torque =

<xx>%

@40 Torque =

<xx>%

@50 Torque =

<xx>%

@60 Torque =

<xx>%

@70 Torque =

<xx>%

@80 Torque =

<xx>%

@90 Torque =

<xx>%

YES

@10 Torque =

<xx>%

@20 Torque =

<xx>%

Display Close

Torque

Archive?

YES

@30 Torque =

<xx>%

@40 Torque =

<xx>%

@50 Torque =

<xx>%

@60 Torque =

<xx>%

@70 Torque =

<xx>%

@80 Torque =

<xx>%

@90 Torque =

<xx>%

DISPLAY

TORQUE ARCHIVE

NO
OR

NEXT

YES

REMOTE

DISPLAY#2

<rem_disp#2_state>

<state: NORMAL/

NOT CONFIGURED/

LOST LINK/FAILED>

YES

BACK

NEXT

YES

APD Module

<apd_state>

<state: NORMAL/

FAILED>

Inside

Temperature=

<xx>C

YES

DISPLAY

HARDWARE?

EXIT?

Strokes

<xxx,xxx,xxx>

Motor

Run Time

<hr:min:sec>

YES

DISPLAY

OPERATE ARCHIVE?

DISPLAY OPERATION ARCHIVE

Figure 6-5

NO
OR

NEXT

BACK

NEXT

YES

Motor
Starts

<xxx,xxx,xxx>

YES

Strokes

<xxx,xxx,xxx>

Motor

Run Time
<hours>

Central Control

<cen_ctrl_state>

<state: NORMAL/

LOST LINK /FAILED>

Local Display

<lcl_disp_state>

<state: NORMAL/

LOST LINK /FAILED>

REMOTE

DISPLAY#1

<rem_disp#1_state>

<state: NORMAL/

NOT CONFIGURED/

LOST LINK / FAILED>

Summary of Contents for Bettis 500







































































































Search results

Summary of Contents for Bettis 500

Reviews:

Related manuals for Bettis 500

Brands by name

Popular brands

Emerson Bettis 500, Installation And Operation Manual

Search results

Summary of Contents for Bettis 500

Reviews:

Related manuals for Bettis 500

Brands by name

Popular brands