manualshive.com logo in svg

Emerson Bettis 500, Installation And Operation Manual

Share
Download
Emerson Bettis 500 Installation And Operation Manual Download Page 64

 

February 2018

Installation and Operation Manual

E2K-405-0218 Rev. 2

56

Section 5: Customizing Actuator Settings

Customizing Actuator Settings

Relays #9 through #12 are the auxiliary relays when the Auxiliary Relay Module 
(ARM) is installed. To configure these relay outputs, follow Step No.1 through  
No. 3 listed above. See 

Table 5-3.

NOTE:

The ARM cannot be added when the Controlinc ACM is installed.

Table 5-3. 

Relay Outputs #9 through #12 Configuration

Relay

Default 
Function

Configurable
Function

Configure 
N.O./N.C.

Default
Setting

RO#9

Lost Power

See 

Table 5-2 Relay

Output Function List

Yes

N.O.

RO#10

Motor Overload

See 

Table 5-2 Relay

Output Function List

Yes

N.O.

RO#11

Lost Phase

See 

Table 5-2 Relay

Output Function List

Yes

N.O.

RO#12

Over Torque

See 

Table 5-2 Relay

Output Function List

Yes

N.O.

5.5.6  Inhibit and ESD Setup

1. 

At the 

“INHIBIT AND ESD SETUP?”

 prompt answer 

“YES.”

2. 

Use the selector knob (

NEXT/BACK

) to review the settings for Control 

Inhibits and Emergency Shut Down.

3. 

Use the control knob (

NO

) to select either 

ON

 or 

OFF

 for each setting; 

then answer “

YES.

”

Figure 5-11

 details each setting.

Summary of Contents for Bettis 500







































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands