Emerson Bettis 500 Installation And Operation Manual Download Page 46

Page: 46 / 102

February 2018

Installation and Operation Manual

E2K-405-0218 Rev. 2

Section 4: Operation

Operation

4.5

Remote/Auto Control Operation

The actuator is shipped configured for “four-wire control” unless otherwise specified at
order placement. There are additional remote control modes that can be selected via the
“

SETUP

” mode.

NOTE:

See

Table 4.4

for defaults.

•

Two-wire control

•

Three-wire control

•

IrDA port

•

Three-wire analog

•

Analog

•

Network

For installation details, see

Section 3.5, Discrete Controlled Inputs

To control the actuator via discrete inputs:

Enter “

SETUP

” mode. See

Section 5.1, Entering Setup Mode

Use the selector knob

(NEXT/BACK)

to select “

CONTROL MODE

” under “

VALVE

CONTROL SETUP?

”

Use the control knob

(NO)

to select the desired control mode. See

Section 5.5.2,

Valve Control Setup

Exit “

SETUP

” mode and place selector knob in the REMOTE position.

Remote Maintained – Inching Mode

Apply the control signal and maintain. After 0.5 seconds the actuator will move in
the open or close direction.

Eliminate the control signal to stop the actuator.

Remote Momentary – Seal-ins Active

Momentarily pulse either OPEN or CLOSE control signal for 0.5 seconds minimum.

The actuator will move in the open or close direction to the end of travel.

Momentarily pulse the remote stop signal to stop the actuator movement.

Summary of Contents for Bettis 500







































































































Search results

Summary of Contents for Bettis 500

Reviews:

Related manuals for Bettis 500

Brands by name

Popular brands

Emerson Bettis 500, Installation And Operation Manual

Search results

Summary of Contents for Bettis 500

Reviews:

Related manuals for Bettis 500

Brands by name

Popular brands