manualshive.com logo in svg

Emerson Bettis 500, Installation And Operation Manual

Share
Download
Emerson Bettis 500 Installation And Operation Manual Download Page 48

 

February 2018

Installation and Operation Manual

E2K-405-0218 Rev. 2

40

Section 5: Customizing Actuator Settings

Customizing Actuator Settings

Section 5: Customizing Actuator Settings 

5.1 

Entering Setup Mode

The “

SETUP

” mode must be entered to modify any configuration settings.

1. 

Place the selector knob in the 

STOP

 position. Setup may be performed at any one 

location; i.e. at the LDM or any RDM that is connected.

NOTE:

STOP

 button on the Clicker only stops a moving valve.

2. 

Rotate the control knob to 

YES

, then 

NO

, then 

YES

, then 

NO

 in rapid succession 

and then release. “

SETUP

” icon will be displayed on the display module and 

“

SETUP?

” will be displayed on the message center.

NOTE:

Do not hold the knob in any one position longer than 0.5 seconds.

3. 

Rotate the control knob to 

YES

. A series of questions will be displayed as detailed 

in 

Figure 5-1

.

NOTE:

If the control knob is placed in the 

NO

 position or if 

NEXT

 or 

BACK

 is selected in 

lieu of 

YES

, the display will return to the normal display mode.

4. 

Use the control knob to answer “

YES

” or “

NO

” to the displayed questions.  

Use the selector knob, 

NEXT

 and 

BACK

, to advance through the setup selections.

5. 

When configuring is complete, advance to “

EXIT SETUP?

” Answer “

YES.

”  

The display will return to normal display model.

NOTE:

If a knob entry is not made within 120 seconds, the actuator will exit the “

SETUP

” mode 

and revert to the normal display.

NOTE:

No Passcode is required for viewing any of the settings.  
Passcode will be needed for changing any of the parameters.

Summary of Contents for Bettis 500







































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands