EMBRON Hatteland HD 19T22, User Manual

Page: 61 / 142

61
IND100129-207
All specifications are subject to change without prior notice!
Specifications - NMEA / IEC COM + Digital IO Module
Q170 IO
1/2
This information may not, in whole or in part, be copied, photocopied,
reproduced, translated or reduced to any electronic medium or machine-
readable form without the prior written consent of Hatteland Technology
AS. The products may not be copied or duplicated in any way.
Dimensions might be shown with or without decimals and indicated as mm [inches]. Tolerance on drawings is +/- 1mm. For accurate measurements, check relevant DWG fi le.
DATASHEET
Hatteland Technology AS | www.hattelandtechnology.com | Enterprise no: NO974533146
1/4
Single channel RS-422 / RS-485, NMEA / IEC COM + Isolated Digital IO (2x IN/OUT) Module
Manufacturer:
Hatteland Technology AS
Product: Single channel RS-422 / RS-485, NMEA/IEC COM
+ Isolated Digital IO (2 x 2 x Input) module
Typenumber: Q170 IO
Last Revised: 06 Jul 2021
Revision#: 05
The Hatteland Technology COM+DIO module provide the system with a single NMEA COM (Page 1,2) channel and 2 x Isolated Digital
Output and 2 Isolated Digital Input (page 3). The module is attached to the motherboard and connected internally. Application software
access the NMEA COM channels as standard COM device. Application software access the DIO channels internally, i.e. in the normal
case there is no requirements for low level software development. This module will mainly be integrated, electrical and mechanically for
Series X G2 Panel Computers.
Description:
Internal connection to RS-485 / RS-422 isolated
• Features - Independent channels.
- Outputs are short circuits protected. Inputs are protected.
- Driver strength are approved.
- All channels are fully isolated.
- Classified towards IEC61162-1 and IEC61162-2.
- Tested according to EN61162.
- NMEA-183 Compliant.
- All requirement for usage in ECDIS applications/systems is fulfilled.
• Absolute Max voltage applied to outputs -15V to +15V
• Data Rate / Technical Data Output - Outputs 115kbps (Theoretically 400kbps).
- ±15V ESD protection on all RS-485 signals (Human Body Model - HBM).
- Isolation rating = 500VDC, not intended for connection to live power nets.
• Transmitter enable mode - Standard mode is automatic.
- Standard Mode will accept send by RTS, but will in fact ignore RTS.
- Choose mode in BIOS: "Serial Port 2 Configuration/RS422\RS485 Control":
"Half Duplex, no echo". "Half duplex, with echo". "Full duplex Slave". "Full Duplex Master".
• Cable Connector
Terminal Block 5-pin rows (MC 1,5/ 5-STF-3,81) (see illustration below)
• Recommended Cable Thickness Minimum 22 AWG - Maximum 18 AWG
• Operating System / Drivers supported Standard drivers/port available in Operating System.
• Test and certificate Hatteland Technology standard,
(tested / type approved by the following classification societies):
IEC 60945 4th (EN 60945:2002), IACS E10 , EU RO MR - Mutual Recognition,
ClassNK - Nippon Kaiji Kyokai
Note: Product below for illustration only. Location of module and product size/design may differ. Connector/pinning remain the same.
Illustration and Pinning:
1 Port identified in the Operating System (OS) as COM2 .
RS-485 Half Duplex (2-wire, supports ECHO) Configuration:
Connect TxD and RxD pair-wise: TxD- to RxD-, TxD+ to RxD+.
5-pin Terminal Block 3.81
Details: RS-422 / RS-485, NMEA / IEC COM
5-pin Isolated NMEA COM
“RS-422/RS-485”
5 4 3 2 1
PIN 01 TxD- Transmit Data Negative
PIN 02 TxD+ Transmit Data Positive
PIN 03 GND Isolated Ground
PIN 04 RxD- Receive Data Negative
PIN 05 RxD+ Receive Data Positive
RS-485 Half Duplex (2-wire) Confi guration:
Connect TxD and RxD pair-wise:
TxD- to RxD-, TxD+ to RxD+.
Note: Confi guration of the Duplex Mode and
Force of Transmitter are set in
Computer Mainboard BIOS.
5-pin Isolated NMEA COM
“RS-422/RS-485”
Tx- Tx+ COM Rx- Rx+
1 2 3 4 5
PIN 01* RxD+ Receive Data Positive
PIN 02* RxD- Receive Data Negative
PIN 03* TxD+ Transmit Data Positive
PIN 04* TxD- Transmit Data Negative
PIN 05 GNDR Ground 100Ω
*Pin 1,2,3,4=RS-422/485 Full Duplex (4-wire)
*Pin 3,4 = RS-485 Half Duplex (2-wire)
Note: Confi guration of the Duplex Mode and
Force of Transmitter are set in
Computer Mainboard BIOS.