manualshive.com logo in svg

Electrolux Inspiration EWX11831 TC3, Service Manual

Share
Download
Electrolux Inspiration EWX11831 TC3 Service Manual Download Page 8

Guide to diagnostics of EWX11831 electronic controls 

2013 TS/DT-mdm  FCPD-dp

 8/71 

599 77 00-82 Rev. 01

 

4 DIAGNOSTIC 

SYSTEM 

4.1 Accessing 

diagnostics 

The operations listed below must be carried out within 7 seconds. 

 

TC 3 

TC4 

 

 

 

Do not start the procedure with your fingers over the combination sensors 

 

1.  Switch on the appliance using the ON/OFF 

button. The first LED lights up. 

2.  Simultaneously press the 

START/PAUSE

 

button and the nearest 

option

 

sensor

 (as 

shown in the diagram). 

3.  Hold your fingers over the sensors until the 

LEDs and symbols begin to flash in sequence 
(approximately 3 seconds). 

In the first position, the operation of the sensors, 
the LEDs and the groups of symbols shown on 
the LCD display is checked;  
When the programme selector is turned in a 

clockwise direction

, the operation of the 

various components is diagnosed and the 
alarms are read (see diagnostic test on the next 
page). 

1. 

Set the selector dial to position 0 (zero). 

2. 

Rotate the programme selector by 

one 

position clockwise.

 

3. 

Simultaneously press the 

START/PAUSE

 

button and the nearest 

option

 

sensor

 (as 

shown in the diagram). 

4. 

Keep your fingers above the sensors until 
the LEDs and display symbols start 
flashing. 
 

In the first position, the operation of the buttons 
and the related LEDs is checked; turn the 
programme selector dial 

clockwise

 to run the 

diagnostic cycle for the operation of the various 
components and to read any alarms (see 
diagnostic test on the next page). 

4.2 

Quitting the diagnostics system 

 

Styling TC4

: To exit the diagnostics system, turn the selector dial to position 0 (zero).

 

 

Styling TC3

: In order to exit the diagnostic system turn the appliance off using the ON/OFF push button.

 

 
If “ELE” (electricity trials) appears on the screen when you turn the appliance on, repeat the operation of 
turning it on and off. 
 
 

Summary of Contents for Inspiration EWX11831 TC3








































































Reviews:

No comments

Brands by name

Popular brands

Load more brands