Electrolux Inspiration EWX11831 TC3 Service Manual Download Page 50

Page: 50 / 71

Guide to diagnostics of EWX11831 electronic controls

2013 TS/DT-mdm FCPD-dp

50/71

599 77 00-82 Rev. 01

Checks to perform:

E62

E62: Overheating during washing

E62

The temperature of the NTC probe exceeds 88



C for more than 5 mins.

MAIN CIRCUIT

BOARD



Ω



Ω

Washing heating

element

5.7 ÷ 6.3K



(20°C)

5.7 ÷ 6.3K



(20°C)



Ω

Fig. 6

Measure the NTC probe

between terminals J3-4 and

J3-5 of the main circuit

board connector.

Is the value correct?

(between 5.7 and 6.3K



20°C)

Run the diagnostic cycle

and fill with water up to the

door level to make sure the

heating element is

completely submerged.

Measure between the wiring
connector J6-1/J6-2 and the

appliance body.

(see fig 6)

Is the circuit open?

Detach the connector and

measure between the

heating element and the

earth contact.

- (see fig. 19)-

Is the circuit open?

Replace the heating

element and repeat the

diagnostic cycle to check

for any further alarms.

Check/replace the wiring and repeat the diagnostic cycle to check

for any further alarms.

Detach the connector and

measure the value directly

on the NTC probe.

- (see fig. 18)-

Is the value correct?

(between 5.7 and 6.3K



20°C)

Replace the heating

element and repeat the

diagnostic cycle to check

for any further alarms.

Replace the circuit board

and repeat the diagnostic

cycle to check for any

further alarms.

Check/replace the wiring and repeat the diagnostic cycle to check

for any further alarms.

If there are burns on the circuit board,

see page 69

Check that all the connectors are correctly inserted

Fig. 18

Fig. 19

Y
E
S

Summary of Contents for Inspiration EWX11831 TC3








































































Search results

Summary of Contents for Inspiration EWX11831 TC3

Reviews:

Brands by name

Popular brands

Electrolux Inspiration EWX11831 TC3, Service Manual

Search results

Summary of Contents for Inspiration EWX11831 TC3

Reviews:

Brands by name

Popular brands