manualshive.com logo in svg

Electrolux Inspiration EWX11831 TC3, Service Manual

Share
Download
Electrolux Inspiration EWX11831 TC3 Service Manual Download Page 7

Guide to diagnostics of EWX11831 electronic controls 

2013 TS/DT-mdm  FCPD-dp

 7/71 

599 77 00-82 Rev. 01

 

2  APPLIANCE CONTROL PANELS  

 

These are the stylings available at the time of printing of this Service Manual. Others may be developed in 
future.

 

3  PROGRAMMING/UPDATING THE MAIN BOARD  

 

 

 

 

Any programming / updating / diagnostics operation carried out with the 
board inserted in the machine and the mains plug disconnected from the 
socket. 

 

 

If one of these operations is accidentally carried out when plugged in to the 
socket, on completing the operation, the appliance will remain turned off 
when restarting; disconnect the plug from the socket and wait at least  
40 minutes before starting up the appliance (any operation will only create 
further delay). 

 

 

In the Service Notes the main circuit board (587) is identified with two spare parts codes: 
 
 
 
 

  Code 973 914… identifies the pre-programmed board. 

  Code 132… identifies the unprogrammed board. 

 
The circuit board can be programmed/updated using the 

Sidekick

 application.

 

For further information, please refer to the instructions provided/illustrated in the course entitled <<

 Guide 

to Sidekick

 >> at the address (http://electrolux.edvantage.net) on the Electrolux Learning Gateway portal. 

 
 
 
To update/program the main board, insert the 

Sidekick

 connector in 

the position shown by the red arrow: 
 
 

 
 
 

T

H

E INSPIRAT

ION RANGE 

TC4 

 

TC3 

587 

Summary of Contents for Inspiration EWX11831 TC3








































































Reviews:

No comments

Brands by name

Popular brands

Load more brands