Electrolux Inspiration EWX11831 TC3 Service Manual Download Page 62

Page: 62 / 71

Guide to diagnostics of EWX11831 electronic controls

2013 TS/DT-mdm FCPD-dp

62/71

599 77 00-82 Rev. 01

EC1

EC1: Water fill solenoid valves blocked

EC1

The flowmeter has to fill water even with the solenoid valve not piloted

Checks to perform:

Open the drawer to

check which solenoid

valve is leaking and

replace it.

Repeat the

diagnostic cycle to

check for any further

alarms.

Does the solenoid

valve start filling with
water as soon as the

appliance is turned on?

Open the drawer where the solenoid

valve leaks to check and measure

between the wiring connectors of the

respective solenoid valve and the

appliance body if there are

dispersions

(fig.6 and tab. 1).

Is there any dispersion?

Replace the main circuit

board and repeat the

diagnostic cycle to check for

any further alarms.

Does the

appliance fill with

water when the

appliance is turned

off?

Replace the main circuit board

and repeat the diagnostic cycle to

check for any further alarms.

Replace the wiring and repeat the diagnostic cycle to check for any further

alarms.

Check that all the connectors are correctly inserted

Fig. 6

Between J18-1 and J18-3 wash solenoid valve
Between J18-4 and J18-6 pre-wash solenoid valve
Between J20-1 and J20-3 third solenoid valve
Between J20-4 and J20-6 hot water solenoid valve

Tab. 1

MAIN CIRCUIT

BOARD

3rd SOLENOID

VALVE

WASH

PRE-

WASH

HOT

WATER

∞

Ω

If there are burns on the circuit board,

see page 69

Y
E
S

Summary of Contents for Inspiration EWX11831 TC3








































































Search results

Summary of Contents for Inspiration EWX11831 TC3

Reviews:

Brands by name

Popular brands

Electrolux Inspiration EWX11831 TC3, Service Manual

Search results

Summary of Contents for Inspiration EWX11831 TC3

Reviews:

Brands by name

Popular brands