Electrolux Inspiration EWX11831 TC3 Service Manual Download Page 65

Page: 65 / 71

Guide to diagnostics of EWX11831 electronic controls

2013 TS/DT-mdm FCPD-dp

65/71

599 77 00-82 Rev. 01

Checks to perform:

EH3

EH3: Supply voltage too low

EH3

Supply voltage value higher than the one configured

EH4

EH4: “zero watt” relay not functioning

EH4

EHE

EHE: Inconsistency between safety relay (main circuit board) and

safety “sensing” circuit

EHE

EHF

EHF: Safety sensing circuit faulty

EHF

Input voltage microprocessor wrong

Is the supply line disturbed or the mains voltage

out of range?

Replace the main circuit board and repeat the

diagnostic cycle to check for any further

alarms.

Have the electrical system of the home
checked / repaired by the proper Body.

Important!

The appliance remains in alarm status until the mains frequency returns to the correct

values or the appliance is switched off (programme selector set to “0”). Only the family of

the alarm is displayed and the diagnostics mode cannot be accessed. The complete

alarm can only be read when the situation has normalised.

Check that all the connectors are correctly inserted

If there are burns on the circuit board,

see page 69

Replace the main circuit board and repeat the diagnostic cycle to check for any

further alarms.

Check that all the connectors are correctly inserted

If there are burns on the circuit board,

see page 69

Check that all the connectors are correctly inserted

If there are burns on the circuit board,

see page 69

Replace the main circuit board and repeat the diagnostic cycle to check for any

further alarms.

Check that all the connectors are correctly inserted

If there are burns on the circuit board,

see page 69

Replace the main circuit board and repeat the diagnostic cycle to check for any

further alarms.

Y
E
S

Summary of Contents for Inspiration EWX11831 TC3








































































Search results

Summary of Contents for Inspiration EWX11831 TC3

Reviews:

Brands by name

Popular brands

Electrolux Inspiration EWX11831 TC3, Service Manual

Search results

Summary of Contents for Inspiration EWX11831 TC3

Reviews:

Brands by name

Popular brands