Ecosys M6526cdn Type B Operation Manual Download Page 20

Page: 20 / 206

Part Names and Functions

1-4

Machine

This chapter explains the names of parts of the fax device.

For the parts required when functions other than FAX are used, refer to the machine’s

Operation Guide

IMPORTANT:

You cannot automatically receive a fax when the main power switch is turned off. To put the

machine to sleep, press the

Energy Saver

key on the operation panel.

Operation panel

Perform the fax operation with this panel.

Main power
switch

Set this switch to ON when performing the fax
or copier operation. The message display
lights to enable operation.

MP (Multi
Purpose) tray

Set the paper in this tray when using a type of
paper other than the cassette (e.g., when
using special paper).

LINE connector

Connect the modular cord for the telephone
line to this connector.

TEL connector

When using a commercially available
telephone set, connect the modular cord to
this connector.

Summary of Contents for M6526cdn Type B















































































































































































































Search results

Summary of Contents for M6526cdn Type B

Reviews:

Related manuals for M6526cdn Type B

Brands by name

Popular brands

Ecosys M6526cdn Type B, Operation Manual

Search results

Summary of Contents for M6526cdn Type B

Reviews:

Related manuals for M6526cdn Type B

Brands by name

Popular brands