Ecosys M6526cdn Type B Operation Manual Download Page 127

Page: 127 / 206

Checking Transmission Results and Registration Status

5-13

Confirmation Screen of Destinations

When selecting

for

Destination Check before Send

, the confirmation screen of destinations appears after

pressing the

Start

key. For details, refer to

Destination confirmation screen before transmission

in the

Operation

Guide

for the machine.

Follow the steps below to confirm the destinations.

Press the





key to confirm every destination.

To confirm a destination, select the destination and
press the

key, and then select [Detail] and

press the

key.

To delete a destination, select the destination you
want to delete and press the

key, and then

select [Delete] and press the

key. Press [Yes]

(the

Left select

key) in the confirmation screen.

The destination is deleted.

Press [Next] (the

Right Select

key).

Press the

Start

key to start sending.

Destination List:

[email protected]

*********************

0676543210

[ Cancel ] [ Next ]

0123456789

Summary of Contents for M6526cdn Type B















































































































































































































Search results

Summary of Contents for M6526cdn Type B

Reviews:

Related manuals for M6526cdn Type B

Brands by name

Popular brands

Ecosys M6526cdn Type B, Operation Manual

Search results

Summary of Contents for M6526cdn Type B

Reviews:

Related manuals for M6526cdn Type B

Brands by name

Popular brands