Ecosys M6526cdn Type B Operation Manual Download Page 195 | Manualshive

Page: 195 / 206

background image

Appendix-13

U01700 - U01720

Communication error occurred during high-speed
transmission. Send again.

U01721

Communication error occurred during high-speed
transmission. Designated transmission speed
may not be available for the recipient machine.
Reduce the transmission start speed and send
again.

U01800 - U01820

Communication error occurred during reception of
high-speed transmission. Ask the sender to
reduce the transmission speed and send again.

U01821

Communication error occurred during reception of
high-speed transmission. Designated
transmission speed may not be available for this
machine. Ask the sender to reduce the
transmission speed and send again.

U03000

During polling reception, a fax could not be
received because no originals were set in the
other party’s fax machine. Check with the other
party.

U03200

Sub address bulletin board reception was
attempted and the other party’s machine is an our-
brand model, but the specified sub address box
contained no data. Check with the other party.

U03300

An error occurred due to either 1 or 2 below.
Check with the other party.

1

The other party’s machine is an our-brand
model and transmission restrictions were
found set by the other party during polling
reception. Communication was interrupted
because the password was incorrect.

2

The other party’s machine is an our-brand
model and transmission restrictions were
found set by the other party during sub
address bulletin board reception.
Communication was interrupted because the
password was incorrect.

U03400

Polling reception was interrupted because the
password entered by the other party did not match
the Local FAX ID on the receiving machine. Check
with the other party.

Error Code

Possible Cause/Action

«
...
193
194
195
196
197
...
»

Summary of Contents for M6526cdn Type B















































































































































































































Reviews:

No comments

Related manuals for M6526cdn Type B

image Prograf iPF785 Series

Brand: Canon Pages: 136

Brand: GBC Pages: 110

Brand: Panasonic Pages: 102

Brand: DataCard Pages: 8

Brand: DataCard Pages: 8

Brand: DataCard Pages: 3

WorkCentre 7655

Brand: Xerox Pages: 24

PR-INT-MX-RAVAS-ABLE

Brand: Ravas Pages: 26

C5020N - FS Color LED Printer

Brand: Kyocera Pages: 410

Brand: Xerox Pages: 2

VersaUV LEJ-640

Brand: Roland Pages: 321

Brand: Oki Pages: 2

Brand: Gestetner Pages: 144

Brand: Unisys Pages: 144

Brand: L-Mark Pages: 62

Brand: IBM Pages: 128

Brand: Epson Pages: 89

EasyFlow WorkForce 30

Brand: Epson Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands