Eaton LMS Installation Manual Download Page 96 | Manualshive

Page: 96 / 202

Eaton LMS Installation Manual Download Page 96

1

L i n e a r I n c l i n e
H o o k - o n S h e l v e s

Tools Required

  -Plastic Mallet
  -Phillips head screwdriver
  -Flat blade screwdriver

1. Assemble the

Front Stop

to the shelf, using the #10AB

x
1-3/4” phillips pan head thread forming screws
provided.
See

Figure 1

.

Note
The front stop must be installed on the Incline Shelving
to prevent equipment from sliding forward and off the
shelf. If your equipment can be safely secured to the
shelf (Wright Line suggests using “Safety Fasteners”),
hole plugs are provided in lieu of Front Stop assembly.

2. Determine the location of the shelf. Position the

Shelf

Supports

as shown in

Figure 2

. Insert the hooks on the

back of the supports into the slotted standard of the Full
Frame and push down.

To assure the hooks are seated, tap the top rear corner
with a plastic mallet or equivalent

Note
Two shelf supports are required for 24”, 30”, 36” and
42” wide shelves.

Three shelf supports are required for 48” and 60” wide
shelves.

Figure 2

Figure 1

83121

technical furniture

Incline Shelving

Full Frame

Slotted standard

1”

R.H. Shelf support

Shelf support
(left/right hand)

L.H. Shelf support

I-1

Incline shelf

#10AB x 1-3/4” phillips
pan head thread forming
screws

Front stop

«
...
94
95
96
97
98
...
»

Summary of Contents for LMS











































































































































































































Reviews:

No comments