manualshive.com logo in svg

Eaton LMS, Installation Manual, Page: 139 / 202

Share
Download
Eaton LMS Installation Manual Download Page 139

C o r n e r   C o n n e c t o r -  
T o p   A c c e s s  
H o r i z o n t a l   C a b l e  
M a n a g e m e n t  

86264 

Please read these instructions carefully and follow 
the installation steps in sequence. 
  

Tools Required

 

     -Phillips head screwdriver 
  
  
The 

Corner Connector

 is used with Top Access Cable 

Management in Tech Corner applications. 
  
The Top Access Horizontal Cable Management sections  
must be installed on either side of the Tech Corner Post 
before installing the Corner Connector. 
  
1. Install a 

Support Bracket

 into the botom of each  

    Top Access Horizontal Cable Management section. 
    See 

Figure 1

. 

  
2. Place the Corner Connector assembly onto the two 
    Support Brackets and fasten it to the brackets with  
    the four #10AB x .25” Sheet metal screws provided. 
    See 

Figure 2

. 

  
    

NOTE

: To remove the Cover, move it away from the  

                 Corner Post and lift upward. 
                  

Corner Connector 

Figure 1 

Figure 2 

Tech corner post 

Support bracket 

Top access horizontal 
cable management 

Corner connector  
assembly 

#10AB x .25” Sheet 
metal screws 

Cover 

 
 

  

technical furniture 

M-4 

Summary of Contents for LMS











































































































































































































Reviews:

No comments