Eaton LMS Installation Manual Download Page 87 | Manualshive

Page: 87 / 202

Eaton LMS Installation Manual Download Page 87

L o c k i n g
C o m p a r t m e n t

RECEEDING DOOR INSTALLATION

1. Place the

Receeding Door

assembly face up on top of

the Locking Compartment. See

Figure 5

. Position the

two

Door Track

hinges against the front flange of the

Top. The Door edges must be aligned with the outer sur-
faces of the End Panels. Align the slots in the Door Track
hinges with the six holes in the front flange of the Top.
Install and tighten six #8 Phillips head sheet metal screws
into the Door Track hinges to secure them. See

Figure 5

.

To operate the Receeding Door, grasp the lower edge of
the door panel near the center and pull the door all the way
  toward you. Carefully lower the door to the closed position.
Reverse this procedure to open the door.

NOTE

: Never allow the Receeding Door to slam closed.

Personal injury or damage to the unit may result.

TOP INSTALLATION

1. Before installing the

Top

, make sure that the three screws

at the top of each End Panel is backed out 1/8”(3mm) as
shown in

Figure 3

.

2. Position the Top between the End Panels above the screws.

NOTE

: The Receeding Door mounting holes must face to-

wards the front. Lower the Top so that all six screws en-
gage their corresponding slots in the Top. Next, tighten
the screws to secure the Top. See

Figure 4

.

80172

technical furniture

G-2

Figure 4

Top

Screws

End panel

Receeding door
mounting holes

Shelf

Figure 5

Front flange

Receeding door

Door track hinge

#8 Phillips head
screws

End panel

Door track

«
...
85
86
87
88
89
...
»

Summary of Contents for LMS











































































































































































































Reviews:

No comments