Eaton LMS Installation Manual Download Page 101

Page: 101 / 202

B a s i c P l u s C o r n e r
L a m i n a t e S h e l f

Corner Laminate Shelves

BASICP

Figure 1

technical furniture

Figure 2

Shelf

Shelf support
(L.H. shown)

Pre-drilled hole

#10AB x 5/8” phillips
head screw

Tools Required

-Plastic mallet
-Phillips head screwdriver

1. Determine the location of the

Corner

Laminate Hook-on Shelf

. Position the

Shelf

Supports

as shown in

Figure 1

. Insert the

hooks on the back of the supports into the
slotted standards and push down.

Note
Ensure that the left hand and right hand
supports are installed as shown.

To assure the hooks are seated, tap the top
rear corner of the supports with a plastic
mallet or equivalent.

2. Install the

Rear Support

. Ensure that it is

located at the same height as the right hand
and left hand supports. See

Figure 1

3. With two people, lift and place the shelf
on the shelf supports.

Note
It will be necessary to lift the shelf at an angle
to clear the uprights.

4. Fasten the shelf to the left hand and right
hand supports using the four #10AB x 5/8”
long screws provided. See

Figure2

Maximum Shelf Loading
The maximum shelf loading is 300 lbs
regardless of size.

R.H. Shelf support

L.H. Shelf support

Rear support

Corner post

J-3

Summary of Contents for LMS











































































































































































































Search results

Summary of Contents for LMS

Reviews:

Eaton LMS, Installation Manual, Page: 101 / 202

Search results

Summary of Contents for LMS

Reviews: