manualshive.com logo in svg

Eaton LMS, Installation Manual, Page: 115 / 202

Share
Download
Eaton LMS Installation Manual Download Page 115

R a c k   M o u n t   M o d u l e    
P l e x i g l a s s   D o o r  
( c o n t . )  

2. With one person holding the Door, align the holes in 
    the Hinge with the pre-drilled holes in Left Hand Side 
    Panel. Fasten the door to the Side Panel using the #8 
    AB x .50 Phillips head screws. See 

Figure 2

. 

  

3. If necessary, adjust the 

Magnetic Catch(s) 

(which are  

    mounted on the Door Stop) so that it contacts the Door  
    with the Rubber bumpers on the Door. 
  
    

NOTE

: The 56”, 66”, and 79” high doors are each pro- 

    vided with three catches to provide additional door re- 
    tention. 
  
    If the retention is found to be too great, one or more of 
    the catches can be moved away from the door face or 
    removed.  
  
    The Magnetic Catch(s) can be moved in or out by loosen- 
    ing the two #4-40 Machine screws. Re-position the  
    Catch(s) to the desired location and tighten the screws 
    securely. See 

Figure 3

. 

Rack module 

L.H. Side panel 

Pre-drilled holes 

Door 

Hinge 

#8AB x 1/2” Phillips 
head thread forming  
screw 

Rubber bumper 

Figure 2 

#4-40 Machine 
screw 

Door stop 

Magnetic catch 

Figure 3 

82032 

 
 

  

technical furniture 

K-12 

Summary of Contents for LMS











































































































































































































Reviews:

No comments