Eaton LMS Installation Manual Download Page 76 | Manualshive

Page: 76 / 202

Eaton LMS Installation Manual Download Page 76

S t e e l S h e l v i n g

87396

Please read these instructions carefully and follow
the installation steps in sequence.

Tools Required

-Phillips head screwdriver

-Plastic mallet
-3/8” Wrench

1. Determine the desired location of the

Steel Shelf

and attach the

Brackets

to the frame as shown in

figure 1

.

NOTE

: Be sure that the Brackets are at the same

level.

Tap the top of each Bracket with a plastic mallet
to be that the hooks are fully seated.

2. Lock the Brackets in place by installing a 1/4” -20
x 1/2” hex washer head thread forming screw using
a 3/8” wrench. See

figure 1

.

3. With two people, carefully place the Shelf onto the
Brackets and align the holes in the bottom of the
Shelf with the holes in the Brackets. Fasten the
shelf in place using three #10-24 x 1/2” phillips
head thread forming screws on each side.
   See

figure

2

.

NOTE

: It may be necessary to rotate the Shelf

180° to align the attachment holes.

MAXIMUM SHELF LOADING

The recommended maximum shelf loading is 300
lbs. Heavy Duty Shelf Supports (LA12) can be
   purchased separately to increase the weight capa-
city of the shelf.

technical furniture

Steel Shelving

Figure 1

Bracket

1/4”-20 x 1/2” hex
washer head thread
forming screw

Frame

Hooks

Slotted standard

Figure 2

Steel shelf

Bracket

Bracket

#10-24 x 1/2” phillips
head thread forming
screws

F-6

«
...
74
75
76
77
78
...
»

Summary of Contents for LMS











































































































































































































Reviews:

No comments