manualshive.com logo in svg

Eaton LMS, Installation Manual, Page: 146 / 202

Share
Download
Eaton LMS Installation Manual Download Page 146

4 ”   x   3 ”   V e r t i c a l  
C a b l e   M a n a g e m e n t  

86920 

Please read these instructions carefully and follow 
the installation steps in sequence. 
  

Tools Required 
     

-Plastic Mallet 

     -Phillips head screwdriver 
  

NOTE

: The 

4” x 3” Vertical Cable Management 

is 

available in various lengths. (i.e. 12”, 24”, 36” ect.) 
  
A minimum gap of .50” is required between the Vertical 
and Horizontal Cable Management, top and 
bottom, for a total of 1.00”. 
  
It is recommended that the Vertical and Horizontal  
Cable Management be installed at the same time. 
  
If this is not possible, gaps greater than .50” (1.00” 
total) may be necessary. In this case, some of the Hori- 
zontal Cable Management may have to be repositioned 
to obtain the desired configuration. 
  
The 4” x 3” Vertical Cable Management can only be  
installed on 

intermediate

 

standards. 

  
1. Ensure that the total space between the two Horizon- 
    tal C/M sections is a minimum of 1.00” greater than 
    the length of the Vertical C/M section(s) being install- 
    ed. Adjust as necessary. See 

figure 1

. 

INSTALLATION BETWEEN TWO HORIZONTAL 
CABLE MANAGEMENT SECTIONS 

4” x 3” Vertical Cable 

Figure 1 

Frame 

Intermediate 
standards 

Horizontal Cable 
Management 

Vertical Cable 
Management 

 
 

  

technical furniture 

M-11 

Summary of Contents for LMS











































































































































































































Reviews:

No comments