manualshive.com logo in svg

Eaton LMS, Installation Manual, Page: 133 / 202

Share
Download
Eaton LMS Installation Manual Download Page 133

3 

T e c h   W a l l    
( c o n t . )  

Tech Walls 

may be installed onto Full Frames that 

have other components on one side.  If  the Frames 
have components installed on both sides, they must be 
removed from one side prior to panel installation. 
 
1.  Attach a single Steel Mounting Channel to the left   
     or right  side of each Full Frame section.  See  
     

Figure

 

1

. 

 
2.  Install the panels, from the bottom up, onto the  
     single Mounting Channel.  See 

Figure 2

. 

 

Panel Installation with Components Pre-installed on One Side of Frame

 

 

Full frame standards 

Mounting channel 

Figure 1 

 
3.  With all panels in place, insert the second Mount-  
     ing  Channel into the 

Vertical Panel

 

Retainer

.    

     See 

Figure 3a

. Align Frame tabs with the slots on   

     the channel. 
 
     Rotate the Mounting Channel, align the holes in   
     the channel with the holes in the Frame Standard,   
     and fasten the channel in place, using the #8-32 x  
     3/8” screws. See 

Figure 3b

. 

 
4.  Install the second set of panels onto the side of the  
     Frame without components following the instruc-    
     tions on page L1, step 2. 
 

Components this 
side 

Mounting channel 

Figure 2 

Panel 

Full frame section 

Figure 3a 

Mounting channel 

Panel 

Full frame section 

Vertical panel 
retainer 

Figure 3b 

Panel 

#8-32 x 3/8” screw 

Full frame section 

83646 

 
 

  

technical furniture 

L-3 

Summary of Contents for LMS











































































































































































































Reviews:

No comments