manualshive.com logo in svg

Eaton LMS, Installation Manual, Page: 131 / 202

Share
Download
Eaton LMS Installation Manual Download Page 131

1 

T e c h   W a l l    

Tools Required

 

     -Phillips head screwdriver 
     -Plastic mallet 
     -Flat file 
 

Tech Walls

  are available as fabric covered or 

perforated steel partitions.  These instructions are 
applicable for both types of panels. 
 
Panels are provided in various widths and heights, 
depending on the size of the Full Frame.   
 

IMPORTANT!

 

Tech walls 

cannot

  be installed on Full Frames 

shipped prior to 12/26/95, as the space between the 
Slotted Standards varies. 
 

NOTE

: For ease of installation, it is recommen-     

              ed that the panels be installed onto the  
              Full Frames prior to the installation of  
              any other components. (ie.worksurfaces,  
              shelves, ect.). If this is not possible,   
              proceed to page _  for panel installation  
              with components pre-installed on one  
              side of the Full Frame. 
 
1. Attach the steel 

Mounting Channels

 to the side   

    of the Full Frame Slotted Standards, using the  
    #8-32 x 3/8” Phillips pan head thread forming   
    screws provided.  See 

Figure 1a

. 

 
2. Install the Mounting Channels

 

with the end  

    having the embossed triangle at the top.   
    Align the holes in the Mounting Channel with  
    the pre-punched holes in the Slotted Standards  
    Fasten the Mounting Channel in place with a  
    screw in each hole.  See 

Figure 1b

. 

 
 

Figure 1a 

Figure 1b 

83646 

Mounting channel 

Full frame slotted 
standard 

#8-32 x 3/8” Phillips 
pan head screws 

Embossed triangle 

Front view of mounting channel 

 
 

  

technical furniture 

L-1 

Summary of Contents for LMS











































































































































































































Reviews:

No comments