Eaton EFX48 e-Fuse Series Installation And Operation Manual Download Page 47

Page: 47 / 161

IPN March 2019

Rear View



AC cord sockets to suit IEC plugs, or (see inset)
ac cords fitted to some models (one per rectifier
position)



Protective earthing terminal (M6). See details on
page 59.

Rectifiers

RM3-340/440 Series are fitted with either 48V, 2000W (APR48-ES) rectifier. The rectifiers are fan

-cooled and hot -pluggable.



See Specifications on page 138 for further information. See Troubleshooting on page 120

for details of rectifier alarms.

Top: APR48-ES



Power On LED (Green)



Minor Alarm LED (Yellow)



Major Alarm LED (Red)



Serial Number



Retaining Screw. Tighten to 1.5Nm
(13.3 inch-pounds).





Summary of Contents for EFX48 e-Fuse Series


























































































































































Search results

Summary of Contents for EFX48 e-Fuse Series

Reviews:

Related manuals for EFX48 e-Fuse Series

Brands by name

Popular brands

Eaton EFX48 e-Fuse Series, Installation And Operation Manual

Search results

Summary of Contents for EFX48 e-Fuse Series

Reviews:

Related manuals for EFX48 e-Fuse Series

Brands by name

Popular brands