Eaton EFX48 e-Fuse Series Installation And Operation Manual Download Page 59

Page: 59 / 161

Installation

IPN March 2019

Step 3 - Fit brackets in alternate position (if required)



Rack-mounting bracket (available for 19-inch
and 23-inch wide racks)



Alternative bracket positions

Step 4 - Replace top cover

Procedure complete

Task 3 - Mount the RM3-340/440 in the Rack

Step 1 - Check clearances

RM3-340/440s require the following minimum clearances for access and adequate air

flow:

Front:

24" (600mm)

Rear:

4” (100mm)

Above/below: No restriction

Step 2 - Mount the RM3-340/440

Fit cage nuts in the correct positions to match the screw holes in the RM3-340/440

rack mounting brackets.

Summary of Contents for EFX48 e-Fuse Series


























































































































































Search results

Summary of Contents for EFX48 e-Fuse Series

Reviews:

Related manuals for EFX48 e-Fuse Series

Brands by name

Popular brands

Eaton EFX48 e-Fuse Series, Installation And Operation Manual

Search results

Summary of Contents for EFX48 e-Fuse Series

Reviews:

Related manuals for EFX48 e-Fuse Series

Brands by name

Popular brands