Eaton EFX48 e-Fuse Series Installation And Operation Manual Download Page 65

Page: 65 / 161

Installation

IPN March 2019



Mid-point Monitoring sense wire from
the EFX48 GPIO terminals



Middle interconnecting link

Procedure complete

Task 7 - Mount the Battery Temperature Sensor

The EFX48 is offered with a battery temperature sensor with a standard 2m (6.5 feet) long cable,

which can be plugged into the temperature sensor socket on the front panel. This sensor

measures the ambient air temperature around the batteries. This is required for the temperature

compensation control process.

Step 1 - Connect and route cable

Connect the temperature sensor cable supplied to the temperature sensor socket

accessible via the EFX48 front panel.

Route the temperature sensor cable to the middle battery shelf or the middle of

the external battery stand.



Do not run the sensor cable along ac supply cables. Interference may cause

false readings.

Summary of Contents for EFX48 e-Fuse Series


























































































































































Search results

Summary of Contents for EFX48 e-Fuse Series

Reviews:

Related manuals for EFX48 e-Fuse Series

Brands by name

Popular brands

Eaton EFX48 e-Fuse Series, Installation And Operation Manual

Search results

Summary of Contents for EFX48 e-Fuse Series

Reviews:

Related manuals for EFX48 e-Fuse Series

Brands by name

Popular brands