manualshive.com logo in svg

E.J. Ozone Products ME800 series, Instruction Manual, Page: 75 / 93

Share
Download
E.J. Ozone Products ME800 series Instruction Manual Download Page 75

EOP-D73-001-7-002-05E 

E.J. OZONE PRODUCTS 

- 74 - 

●

 If the light intensity of sensor 1 is zero, zero is displayed, or the error display at that time is 

given. 

●

 If the light intensity of sensor 2 is zero, concentration display at that time (analog output) or       

error display is maintained. Note that the error display cannot be reset while the display is 
maintained. 

 

The order of precedence of errors is shown below. 
*  Measurement mode: 

E0 < E1 < 

Sensor light intensity alarm display

 < E3   

 

  < Lamp abnormal emission < E6 (ON) or E6 (Blink) 

*  At the time of zero calibration:  E0 < 

Sensor light intensity alarm display

 < E3   

 

  < Lamp abnormal emission < (E2) < E6 (ON) or E6 (Blink) 

 

Superiority of E6 (ON) and E6 (Blink): E6 (Blink) < E6 (ON) 

 

Table- 5    Self-diagnostic error operation 

Startup 

operation 

Item 

Output signal 

Input signal 

Display 

Lamp control 

voltage alarm

OUT1

(MES)

OUT2,3 
(AL1/2) 

OUT4 
(PA1) 

OUT5

(ERR)

OUT6 

(S.V) 

A.OUT
V.OUT

INPUT 

Reset of ERR  “Red” display

No limit 

E0 OFF 

Operated 

Operated

ON 

Operation 

permitted

Operated

Operation 

permitted 

Operation 

permitted 

※

2

 

5 minutes 

E2 OFF 

Operated 

Operated

ON 

ON 

※

1

Operated

Operation 

permitted 

Operation 

permitted 

※

2

 

5 minutes 

Operation 

started in 5 

minutes 

E1 OFF 

Operated 

Operated

ON 

Operation 

permitted

Operated

Operation 

permitted 

Operation 

permitted 

※

2

 

―

 

E3 OFF 

Operated 

Operated

ON 

Operation 

permitted

Operated

Operation 

permitted 

Operation 

permitted 

※

2

 

―

 

E6 ON 

OFF  Maintained Maintained

ON 

Operation 

only 

Maintained

Operation 

only 

―

 

―

 

E6 blinks 

OFF 

Operated  Operated

ON 

Operation 

permitted

Operated

Operation 

permitted 

―

 

―

 

Sensor light 

intensity 

alarm 

ON Operated 

Operated

OFF 

Operation 

permitted

Operated

Operation 

permitted 

―

 

―

 

Operated 

for 5 

minutes 

Warm-up 
operation 

OFF OFF  OFF OFF  OFF 

0V/1V 

/4Ma 

―

 

―

 

―

 

S1

：

Less 

than 0.5V 

OFF Operated 

Operated Operated Operated

0V/1V 

/4mA 

―

 

―

 “Red” 

display

S1

：

More 

than 0.5V 

ON Operated 

Operated

OFF 

Operation 

permitted

Operated

Operation 

permitted 

―

 “Red” 

display

*1: About E2 OUT 6 (S.V) output (ON): Operated during the purge time if operated by zero 

calibration. 

*2 : Operated when the sensor 2 value is normal. Not operated if the light intensity of sensor 2 is 

“0000”. 

 

(1) E0 

E0 is output when the measurement value exceeds the display range. Since the analyzer is 
performing measurement continuously, the error is normally reset if the measurement value falls 
within the display range. 
*  The wait time of “E0” output at the time of startup can be set by “E0 wait time setting” in the 

setting mode. 

  See “5.2.2 Setting mode, (11) E0 wait time setting” for details. 

 

(2) E1 

E1 is displayed when some kind of failure occurs to sensor 1, thus decreasing the light intensity 
of sensor 1. More specifically, E1 is output when the light intensity of sensor 1 decreases to 1/10 
or lower of that of sensor 2. If the light intensity increases, normal operation restarts 
automatically. 
*  Not operated for 5 minutes after the power is turned on. 

 

 

Summary of Contents for ME800 series






























































































Reviews:

No comments