E.J. Ozone Products ME800 series Instruction Manual Download Page 35 | Manualshive

Page: 35 / 93

E.J. Ozone Products ME800 series Instruction Manual Download Page 35

EOP-D73-001-7-002-05E

E.J. OZONE PRODUCTS

- 34 -

(24) Zero calibration mode setting (ZEro)

Zero calibration mode can be selected from manual zero calibration, auto zero calibration, and
intermittent (interval) zero calibration.
* Before changing the zero calibration mode, be sure to check the interval setting time and

purge time.



See “5.4 Zero calibration” for details.

(25) Auto zero interval setting (InT1)

The currently selected auto zero interval setting value is
displayed.
The setting range is from 10 to 60 seconds.
Press the shift switch to select the digit to be changed, and
press the increment switch to select a desired value. The digit
to be changed blinks.
* If a value exceeding the input range is entered, “Err” is displayed.

(26) Intermittent zero interval setting (InT2)

The currently selected intermittent zero interval setting value
is displayed.
The setting range is from 0 to 9999 minutes. Press the shift
switch to select the digit to be changed, and press the
increment switch to select a desired value. The digit to be
changed blinks.
* If 0 min. is selected, zero calibration by timer is not performed.

(27) Intermittent zero purge time setting (Pg)

The currently selected intermittent zero purge time setting
value is displayed.
The setting range is from 0 to 99 seconds. Press the shift
switch to select the digit to be changed, and press the
increment switch to select a desired value. The digit to be
changed blinks.
* If select the time setting of 0 sec, zero calibration cannot be

performed. In addition, the zero calibration becomes invalid
when the power is turned on.

(28) Warm-up operation time setting (UP)

The currently selected warm-up operation time is displayed.
The setting range is from 0 to 99 minutes. Press the shift
switch to select the digit to be changed, and press the
increment switch to select a desired value. The digit to be
changed blinks.
* The factory default setting is “10”.



See “7.1 Preparation for measurement (2) Warm-up
operation” for details.

Increment

Enter

Mode

Zero

calibration

mode (ZEro)

MAnU

AuTo

InT

Increment

Enter

０

０

S

０

０

S

０

１

S

０

０

S

“ ”

“ ”

“ ”

“ ”

Setting
method

０

０

００

“ ”

００

０

０

“ ”

００

１

０

“ ”

００

０

０

“ ”

Setting
method

０

０

S

０

０

S

０

１

S

０

０

S

“ ”

“ ”

“ ”

“ ”

Setting
method

０

０

０

０

０

０

０

１

０

０

０

０

“ ”

“ ”

“ ”

“ ”

Setting
method

«
...
33
34
35
36
37
...
»

Summary of Contents for ME800 series






























































































Reviews:

No comments