manualshive.com logo in svg

Dynamic Engineering PMC-BiSerial-III HW2, User Manual

Share
Download
Dynamic Engineering PMC-BiSerial-III HW2 User Manual Download Page 39

 

 

              

Embedded  Solutions

                       

Page 39 of 50

 

 

Mode Resource Mapping 

 

Mode-Dependent I/O Mapping for a Four-Channel Block 

I/O line 

SDLC Mode   

Async Mode   

 

HW1 Mode   

 

I/O 0   

Transmit Data 

Transmit Data 0 

Transmit/Receive Data 0 

I/O 1   

Receive Data 

Receive Data 0 

Transmit/Receive Data 1 

I/O 2   

Transmit Clock 

Transmit Data 1 

Transmit/Receive Data 2 

I/O 3   

Receive Clock 

Receive Data 1 

Transmit/Receive Data 3 

 
 

Mode-Dependent Interrupt Mapping for a Four-Channel Block 

Int line 

 SDLC 

Mode 

 Async 

Mode 

  HW1 

Mode 

  

Int 0   

Transmit Interrupt  Transmit 0 Interrupt  

Channel 0 Interrupt 

Int 1   

Receive Interrupt 

Receive 0 Interrupt   

Channel 1 Interrupt 

Int 2   

unused 

 

Transmit 1 Interrupt  

Channel 2 Interrupt 

Int 3   

unused 

 

Receive 1 Interrupt   

Channel 3 Interrupt 

 
 

Mode-Dependent Dual-Port RAM Mapping for a Four-Channel Block 

DPR   

SDLC Mode   

Async Mode   

HW1 Mode   

 

DPR 0  

Lo Transmit Buffer  Transmit 0 Buffer 

Channel 0 Buffer 

DPR 1  

Hi Transmit Buffer  Receive 0 Buffer 

Channel 1 Buffer 

DPR 2  

Lo Receive Buffer  Transmit 1 Buffer 

Channel 2 Buffer 

DPR 3  

Hi Receive Buffer  Receive 1 Buffer 

Channel 3 Buffer 

 
Note that all number designations are relative to the number of the first channel in the 
referenced channel block. 

 

Summary of Contents for PMC-BiSerial-III HW2



















































Reviews:

No comments

Brands by name

Popular brands

Load more brands