DynaGen Tough Series, User Manual

Page: 26 / 66

Using the Controller 25
© 2019 DynaGen Technologies Inc
TOUGH Series Manual
False
Restart Warning After going into the RUN mode the controller has determined the engine has not started after all and
will attempt to do another crank attempt. The fault restart feature under Engine Logic > Timers has to
be enabled.
Breaker
Tripped Warning The "Breaker Trip" switched output has been activated. This output is used to control the generator
breaker.
Over
Current Warning The generator AC current has risen above the Over Current warning setpoint under AC Monitor >
O.C. Protection > Basic Alarm.
Fuel In
Basin Warning The "fuel in basin" switched input has been triggered. This indicates there has been a leak in the fuel
tank.
Low
Battery Warning The main starter battery (the battery the controller is powered from) voltage has fallen below the low
battery warning setpoint under Sensors > Battery.
High
Battery Warning The main starter battery (the battery the controller is powered from) voltage has risen above the high
battery warning setpoint under Sensors > Battery.
Low Engine
Temp Warning The engine temperature has fallen below the low engine temperature warning setpoint set under
Sensors > Engine Temp. > Setpoints.
Battle
Running Warning The "Battle Mode" switched input has been triggered. The controller will not shutdown on any failures.
All failures will be ignored.
Under
Frequency Warning The generator AC frequency has fallen below the Under Frequency warning setpoint set under AC
Monitor > Genset Freq. > Setpoints.
Over
Frequency Warning The generator AC frequency has risen above the Over Frequency warning setpoint set under AC
Monitor > Genset Freq. > Setpoints.
Load
Imbalance Warning The generator load is imbalanced between the A, B, and C phases. This has to be enabled under AC
Monitor > O.C. Protection > Imbalance Mode.
Over
Voltage Warning The generator AC voltage has risen above the over voltage warning setpoint set under AC Monitor >
Genset Voltage. Possible issue with the voltage regulator or governing on the engine.
High Fuel
Temp Warning Doosan G2 electronic engine high fuel warning. This warning comes from the engine ECM over CAN
J1939.
Hi Exhaust
Temp Warning Doosan G2 electronic engine high turbine exhaust temperature. This warning comes from the engine
ECM over CAN J1939.
Failed To
Stop Failure The controller shut down the engine -- by turning off the Fuel output and (if enabled) by turning on the
Energize-To-Stop output -- but the engine speed did not go to zero after the energize to stop time
(under Timers > Engine Logic).
Breaker
Failed Failure The "Breaker Trip" switched output failed to turn off the breaker. This is triggered if the AC Current is
still above 10% of the rated current setpoint. The "breaker trip" failure has to be enabled under AC
Monitor > O.C. Protection > Brk Trip Fail.
Load
Imbalance Failure The generator load is imbalanced between the A, B, and C phases. This has to be enabled under AC
Monitor > O.C. Protection > Imbalance Mode with the mode set to ""Shutdown Trip".
Over
Current Failure The generator AC current has risen above the over current failure setpoint set under AC Monitor >
O.C. Protection > Basic Alarm.
ECM
Shutdown Failure Electronic engines only. CAN J1939 DM1 stop lamp is active; the ECM has shutdown the engine.
High
Engine
Temp Failure Engine temperature has risen above the high engine temperature failure setpoint set under Sensors
> Engine Temp.
Low Oil
Pressure Failure Engine oil pressure has fallen below the low oil pressure failure setpoint set under Sensors > Oil
Pressure.
Under
Speed Failure Engine speed has fallen below the under speed failure setpoint set under Sensors > Engine Speed.
Over
Speed Failure Engine speed has risen above the over speed failure setpoint set under Sensors > Engine Speed.
Low Fuel
Level Failure The fuel level has fallen below the low fuel level failure setpoint under Sensors > Fuel Level.
Low
Battery Failure The main starter battery (the battery the controller is powered from) voltage has fallen below the low
battery failure setpoint set under Sensors > Battery.