DriSteem XT Series Installation, Operation And Maintenance Manual Download | Manualshive

Page: 41 / 68

background image

37

XT SERIES INSTALLATION, OPERATION, AND MAINTENANCE MANUAL

WITH HEADER INSIDE OF DUCT FOR HORIZONTAL AIRFLOW

Note: See the instructions for installing Rapid-sorb with the header outside the

duct for horizontal airﬂ ow.

1. Mark and cut holes in ductwork or air handler for steam header

pen e tra tion, con den sate drain piping, and head er support bracket fastener.
Allow 1/8"/ft (1%) header pitch toward the support bracket when you drill
the hole for the header support bracket fastener.

2. Loosely fasten the header in place.

3. Rotate the header 90° so the header stubs point hor i zon tal ly in the duct.

When installing in an air handler, the rotation of the header is often less
than 90°. Typically, due to the condensate drain piping re quire ments, the
header can be set on the ﬂ oor of the air handler, assembled in the vertical
position, and then raised and mounted in place.

4. Mount the dispersion tubes on the header with the slip couplings or hose

cuffs:
• When installing slip couplings for 1½" (DN40) dispersion tubes, take

care not to shear O-rings.

• Set slip coupling on header stub or dis per sion tube so O-ring is resting

on face of tubing.

• Rotate slip coupling while pushing it onto the tubing.

• O-rings are lubricated at factory. If additional lubrication is necessary,

DO NOT use petroleum-based lubricant.

5. Allow the dispersion tubes to rest against the bottom of the duct.

CAUTION

Operate Rapid-sorb within rated steam
capacity

Excessive steam ﬂ ow to the Rapid-sorb
steam dispersion assembly can
cause condensate to exit the tubelets,
which can cause water damage and
standing water in the duct or air
handler.

To avoid condensate exiting the
tubelets, do not operate the Rapid-sorb
beyond its rated capacity.

With header outside of duct for horizontal
airflow

1. Mark and cut holes in the ductwork for the

dispersion tubes. Use the L-bracket as a
template to mark the holes on the duct ﬂ oor.

2. Temporarily, loosely suspend or support the

header below the ﬁ nal location. Vertical
balance point of the dispersion tube length
dictates where the header should be
suspended or temporarily supported.

3. Continue with Step 4 at right.

INSTALLATION

Rapid-sorb

Dispersion:

«
...
39
40
41
42
43
...
»

Summary of Contents for XT Series





































































Reviews:

No comments

Related manuals for XT Series

Brand: air&me Pages: 96

Kenmore 407.53530

Brand: Sears Pages: 32

Brand: ARESA Pages: 14

Brand: Bionaire Pages: 36

Brand: Vitek Pages: 28

Brand: Quincy Pages: 92

Brand: Aircare Pages: 41

Brand: Rohnson Pages: 15

Brand: Clean Air Optima Pages: 210

Brand: Oster Pages: 24

Brand: Timberk Pages: 28

Brand: cecotec Pages: 56

Brand: Hyundai Pages: 20

Brand: Hyundai Pages: 40

Brand: Hyundai Pages: 36

Brand: Lanaform Pages: 96

Brand: Rotel Pages: 24

Brand: Skuttle Pages: 32

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands