DriSteem XT Series Installation, Operation And Maintenance Manual Download

Page: 19 / 68

XT SERIES INSTALLATION, OPERATION, AND MAINTENANCE MANUAL

INSTALLATION

Piping:

Plastic tie

Condensate hose (purchased
separately from DriSteem)

Plastic tie

Hose clamp (provided)

Steam hose
(purchased separately
from DriSteem)

Hose clamp (provided)

To open drain or humidiﬁ er ﬁ ll cup.
Water seal is required, whether condensate is piped to
open drain or returned to humidiﬁ er ﬁ ll cup.

OM-7974

7” (178 mm) water seal

Notes:
• Maximum recommended distance between humidiﬁ er

and XT steam blower is 10’ (3 m).

• Models XTP 042 through 096 are not intended for use

with a steam blower.

OM-7975

7” (178 mm)

water seal

To open drain or
humidiﬁ er ﬁ ll cup.
Water seal is
required, whether
condensate is
piped to open
drain or returned
to humidiﬁ er ﬁ ll
cup.

Plastic tie

Condensate
hose
(purchased
separately
from DriSteem)

Hose clamps
(provided)

Steam hose
(purchased separately from DriSteem)

Hose clamp*

Plastic tie

Steam hose*

Stainless steel Y connector*

* Provided in optional connector

kit Part No. 191070-102

Hose clamp*

Model XTP 025 only

XT steam blowers

FIGURE 15-1: PIPING FROM XT SERIES HUMIDIFIER TO REMOTE XT STEAM BLOWER

Summary of Contents for XT Series





































































Search results

Summary of Contents for XT Series

Reviews:

Related manuals for XT Series

Brands by name

Popular brands

DriSteem XT Series, Installation, Operation And Maintenance Manual

Search results

Summary of Contents for XT Series

Reviews:

Related manuals for XT Series

Brands by name

Popular brands