DriSteem XT Series Installation, Operation And Maintenance Manual Download

Page: 51 / 68

XT SERIES INSTALLATION, OPERATION, AND MAINTENANCE MANUAL

Start-up checklist

Your humidiﬁ cation system may not have all of the options listed below. If an
item does not apply to your system, skip to the next item.

☐

Verify that humidiﬁ er, controls, piping, electrical connections, steam supply,

and dispersion units(s) are installed according to installation instructions in
this manual and:

• Ladder style wiring diagram and external connections wiring diagram

(inside humidiﬁ er cabinet)

• Governing

codes

• Vapor-logic Installation and Operation Manual

– Installation

section

– Pre-installation

checklist

☐

Verify that ﬁ eld wiring is done per instructions in this manual and per unit

wiring diagram.

☐

Conﬁ rm that proper grounding and an approved earth ground are provided.

☐

Conﬁ rm that instructions in the Electric shock hazard warning have been followed.

☐

Conﬁ rm that water ﬁ ll line was thoroughly ﬂ ushed before it was connected to the humidiﬁ er.

☐

Verify that humidiﬁ er is mounted level and securely supported before ﬁ lling with water. See

operating weights in Table 6-1.

☐

Make sure cylinder is fully seated into drain valve, and verify that all electrical connections are

secure.

☐

Turn water supply on (do not use demineralized, deionized, or reverse-osmosis water) and

conﬁ rm that drain valve is closed.

If the force of air exiting water supply lines blows ﬁ ll cup cap off during ﬁ rst ﬁ ll cycle, this is not
a sign of defect or a cause for concern; simply replace ﬁ ll cup cap after all air has exited water
line.

☐

Verify that humidiﬁ er is level and plumb when ﬁ lled with water.

☐

Turn power on and conﬁ rm that Model XTP keypad/display illuminates.

☐

Conﬁ rm that airﬂ ow switch is closed.

☐

If you choose not to use airﬂ ow switch: Jumper AFsw and 24vac terminals

☐

If you choose not to use on-off duct high limit: Jumper 21vdc and DHL terminals

☐

Conﬁ rm that high limit humidistat input is closed or that variable air volume (VAV) control system

high limit transmitter is connected.

☐

With sufﬁ cient water in steam cylinder, airﬂ ow switch closed, high limit humidistat closed, door

safety interlock switch closed, and a call for humidity, verify that heat outputs are activated.

☐

If you experience difﬁ culties, see “Troubleshooting” on Page 52.

WARNING

Electric shock hazard

Contact with energized circuits can
cause property damage, severe
personal injury or death as a result of
electrical shock or ﬁ re.

Make sure cabinet doors are installed
before turning on electrical power.

For proper operation of safety interlock
switch, install electrical-side door ﬁ rst,
then install cylinder-side door.

OPERATION

Summary of Contents for XT Series





































































Search results

Summary of Contents for XT Series

Reviews:

Related manuals for XT Series

Brands by name

Popular brands

DriSteem XT Series, Installation, Operation And Maintenance Manual

Search results

Summary of Contents for XT Series

Reviews:

Related manuals for XT Series

Brands by name

Popular brands