DriSteem XT Series Installation, Operation And Maintenance Manual Download

Page: 65 / 68

XT SERIES INSTALLATION, OPERATION, AND MAINTENANCE MANUAL

Accessories

Table 61-1:
Accessories

Description

Part No.

Steam hose, 1" (DN25) x 10' (3 m), for remote XT steam blower

305400-100

Steam hose, 1

" (DN40) x 10' (3 m), wire-reinforced

305400-010

Steam hose, 2" (DN50) x 10' (3 m), wire-reinforced

305560-0010

Condensate hose, 1/4" (DN8) x 13' (4 m), for remote XT steam blower

305400-150

Drain hose cuff, 1" (DN25) I.D. x 12" (305 mm) long

305389-012

Hose clamp, 1" (DN25) I.D.

700560-100

Hose clamp, 23 mm, spring band

700560-023

Hose clamp, 19 mm, spring band

700560-019

Hose clamp, 1

" (DN40) I.D.

700560-150

Hose clamp, 2" (DN50) I.D.

700560-200

Kit, drip tee, 304 stainless steel, 1

" (DN40)

191071-001

Humidistat, duct high limit, HC-201

405850-201

Humidistat, room, HC-101

405870

Humidity transmitter, duct, 2% RH DSB

405884-009

Humidity transmitter, room, 2% RH

405883-008

Switch, airﬂ ow, AFS-112-150, electric

406190

Kit, Y connector; Models XTP 033, 042, and 048 (see Figure 24-1)

• 1 Y connector, stainless steel, 1

" x 2" (DN40 x DN50)

191070-101

• 2 steam hoses, 1

"(DN40), 12" (305 mm) long

• 4 hose clamps

Kit, Y/tube connectors; Models XTP067 through 096 (see Figure 24-1)

• 2 Y connector kits

191070-101

• 1 ﬂ anged tube connector, stainless steel, 3" (DN80)

162825-202F

Kit, tube connector; Model XTP050 (see Figure 24-1)

• 1 tube connector, stainless steel, 1

" x 2" (DN40 x DN50)

191070-002

• 1 hose cuff, 2" (DN50), 6" (152 mm) long

• 2 hose clamps

Kit, tube reducer; Models XTP 002 through 006 (see Figure 23-1)

• 1 tube reducer, stainless steel, 1" x 1

" (DN25 x DN40)

191070-100

• 1 steam hose, 1" (DN25), 12" (305 mm) long

• 2 hose clamps

Kit, tube Y connector; Model XTP 025 (see Figure 23-1)

• 1 Y connector, 1.5" x 1.5" x 1.5"(DN40 x DN40 x DN40)

191070-102

• 1 steam hose, 1.5" (DN40), 12" (305 mm) long

• 2 hose clamps

MAINTENANCE

Summary of Contents for XT Series





































































Search results

Summary of Contents for XT Series

Reviews:

Related manuals for XT Series

Brands by name

Popular brands

DriSteem XT Series, Installation, Operation And Maintenance Manual

Search results

Summary of Contents for XT Series

Reviews:

Related manuals for XT Series

Brands by name

Popular brands