DriSteem XT Series Installation, Operation And Maintenance Manual Download | Manualshive

Page: 21 / 68

background image

17

XT SERIES INSTALLATION, OPERATION, AND MAINTENANCE MANUAL

Humidifi er wiring

All wiring must be code approved and in accordance with the unit wiring
diagram. Power supply wiring must be rated for 105 °C. See Figure 17-1
for the humidiﬁ er wiring diagram locations.

When selecting a location for installing the humidiﬁ er:

• Avoid areas close to sources of electromagnetic emissions such as power

distribution transformers.

• Do not loop power wiring.

• Do not use aluminum wire.

CONDUIT KNOCKOUTS

Conduit and control wiring knockouts are provided on the XT Series humidiﬁ er
cabinet. See Figure 5-1.

CONTROL COMPONENT PLACEMENT

Follow the guidelines on Page 19 for placing humidistats, transmitters, and
airﬂ ow proving switches.

CAUTION

Adding conduit connections not recommended

Adding alternate conduit connections is not recommended. If you must make
additional holes in the humidiﬁ er cabinet, protect all internal components from
debris, and vacuum out the cabinet when ﬁ nished. Failure to follow these precautions
can damage sensitive electronic components and void the DriSteem warranty.

Notes:
• Control wiring and power wiring must be

run in dedicated or separate earthed metal
conduit, cable trays, or trunking.

• Separate the line voltage wiring from low

voltage control circuit wiring when routing
electrical wiring inside the humidiﬁ er
cabinet.

• Do not use chassis or safety grounds as

current-carrying commons. Never use a
safety ground as a conductor or neutral to
return circuit current.

• For circuit protection requirements, see

recommended fusing in Table 4-1.

OM-7692

Fused disconnect

Power supply

XT Series humidiﬁ er

Wiring
diagram
inside of
humidiﬁ er
cabinet

WARNING

Electric shock hazard

Only qualiﬁ ed electrical personnel
should perform ﬁ eld wiring installation
procedures. Improper wiring or contact
with energized circuits may cause
property damage, severe personal
injury, or death as a result of electric
shock and/or ﬁ re.

INSTALLATION

FIGURE 17-1: FIELD WIRING
REQUIREMENTS

«
...
19
20
21
22
23
...
»

Summary of Contents for XT Series





































































Reviews:

No comments

Related manuals for XT Series

Brand: Klingenburg Pages: 52

ELEKTRA health+

Brand: S&P Africa Pages: 5

Brand: omi Pages: 94

Brand: DeLonghi Pages: 9

Brand: Air Naturel Pages: 24

Brand: Fehom Pages: 22

Brand: GeneralAire Pages: 2

LAVATHERM T37840

Brand: AEG Pages: 125

Brand: AEG Pages: 16

Brand: AEG Pages: 12

Brand: AEG Pages: 28

Brand: Black & Decker Pages: 24

Brand: Black & Decker Pages: 14

Brand: Danby Pages: 24

Brand: Express Pages: 56

Brand: Trotec Pages: 10

Brand: Trotec Pages: 14

Brand: Danby Pages: 22

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands