DriSteem XT Series Installation, Operation And Maintenance Manual Download

Page: 55 / 68

XT SERIES INSTALLATION, OPERATION, AND MAINTENANCE MANUAL

DRAIN VALVE

If either of the following issues occur after several months of runtime, follow the
drain valve maintenance procedures below.

• Drain valve is closed, but draining and ﬁ lling continue.

• End of cylinder life prompt appears prematurely.

DRAIN VALVE BODY MAINTENANCE

1. When steam cylinder is empty, turn humidifier off. Place all power

disconnects in OFF position, and lock in OFF position. See Figure 51-1.

2. Remove cabinet doors and steam cylinder (see Page 10).

3. Vacuum loose scale and debris out of the drain valve port.

4. Disconnect 2-pin Molex plug from 24 VAC drain valve coil.

5. Slide cap (A) off of drain valve coil (C).

6. Turn hex nut (B) counter-clockwise. Loctite on nut will cause drain valve

coil assembly to turn out of drain valve body (G). Remove coil/actuator
assembly from drain valve body. Make sure spring (E) and plunger (F) do
not fall out of actuator (D).

7. Clean plunger (F), spring (E), actuator (D), and plastic drain valve body

(G) with clean water.

8. Reassemble drain valve. When threading actuator (D) into drain valve

body (G), make sure it is not cross threaded. Torque actuator into drain
valve body to 18 in-lb (2.0 N·m).

9. Plug Molex plug into its mating wire harness plug, and slide cap (A) onto

drain valve coil (C).

10. See “Start-up procedure” on Page 48 if returning humidifier to

operation.
Note: If the procedure above did not resolve drain valve issues, perform the

drain valve assembly maintenance procedure on Page 52.

Maintenance:

OM-7631

Drain valve body (G)

Plunger (F)

Spring (E)

Drain valve coil (C)

Nut (B)

Cap (A)

Drain valve body

Ground plate

Drain cup plate

Drain cup

Insert

OM-7630

Drain valve coil

O-ring

Wires to Molex plug

Actuator (D)
Torque to 18 in-lb (2.0 N·m)

Notes:
•

Pay close attention to all parts shown above.
Verify that ground plate is in groove of drain
cup, and insert is in place through ground
plate loop.

•

Failure to get ground plate and insert solidly
connected to frame will compromise ground
safety circuit.

FIGURE 51-1: DRAIN VALVE ASSEMBLY

MAINTENANCE

FIGURE 51-2: DRAIN VALVE BODY

Drain valve

Summary of Contents for XT Series





































































Search results

Summary of Contents for XT Series

Reviews:

Related manuals for XT Series

Brands by name

Popular brands

DriSteem XT Series, Installation, Operation And Maintenance Manual

Search results

Summary of Contents for XT Series

Reviews:

Related manuals for XT Series

Brands by name

Popular brands