manualshive.com logo in svg

DriSteem XT Series, Installation, Operation And Maintenance Manual

Share
Download
DriSteem XT Series Installation, Operation And Maintenance Manual Download Page 12

8

XT SERIES INSTALLATION, OPERATION, AND MAINTENANCE MANUAL

Selecting a location 

HUMIDIFIER

When selecting a location for the humidifi er, consider the following:

•  Proximity to the duct

 

Install the humidifi er near the air duct system where the dispersion assembly 
will be located. The maximum recommended length for steam hose 
connecting a single humidifi er to a dispersion assembly is 10' (3 m). The 
maximum recommended developed length for tubing connecting a single 
humidifi er to a dispersion assembly is 20' (6 m). 

 

For more information about installing dispersion assemblies, see 
“Dispersion” beginning on Page 20.

•  Elevation of the installed dispersion assembly

 

The recommended installation location for the dispersion assembly is at an 
elevation higher than the humidifi er. However, if the dispersion assembly 
must be installed at an elevation lower than the humidifi er, install a drip tee 
and drain. See “Drip tee installation” on Page 29. 

 

Before installing a dispersion assembly or interconnecting piping, review all 
pitch requirements in the “Dispersion” section of this manual.

•  Temperature and relative humidity (RH):

 Install 

humidifi er only in locations that meet the following temperature and 

RH requirements:

 

-  Maximum ambient temperature: 104 °F (40 °C)

 

-  Minimum ambient temperature: 41 °F (5 °C)

 

-  Maximum ambient humidity: 80% RH (non-condensing)

•  Required clearances (see Figure 8-1)

• Electrical connections

 

Electrical power supply connections are at the lower or upper right rear 
corner of the unit. See “Humidifi er wiring” on Pages 17 and 18.

•  Supply water and drain piping connections 

 

Water supply piping and drain connections are at the bottom of the 
cabinet. See “Piping” on Page 13.

•  Exterior wall insulation

 

Install the humidifi er on an exterior wall only if the wall is properly 
insulated.

DISPERSION CONTROL DEVICES

See page 20 for recommended installation locations for the dispersion 
assembly and associated control devices. 

INSTALLATION

 Staging multiple humidifiers

Up to four Model XTP humidifi ers can be 
staged to operate in sequence. In a sequenced 
application, one control input signal is divided 
into user-selectable control input signals for 
the connected humidifi ers. See the 

Vapor-logic 

In stal la tion and Op er a tion Man u al

 for 

instructions on staging multiple humidifi ers. 

16"

(400 mm)

15" (380 mm)

3" (76 mm)
between 
units

3"

(76 mm)

36" (914 mm)
front clearance

OM-7664

FIGURE 8-1:    XT SERIES HUMIDIFIER 
RECOMMENDED MINIMUM CLEARANCES

Summary of Contents for XT Series





































































Reviews:

No comments

Brands by name

Popular brands

Load more brands