DriSteem XT Series Installation, Operation And Maintenance Manual Download | Manualshive

Page: 29 / 68

background image

25

XT SERIES INSTALLATION, OPERATION, AND MAINTENANCE MANUAL

Steam outlet connections with hose

INSTALLATION

Dispersion:

1½" (DN40) hose connections
from two cylinders

2" (DN50) steam hose connection

3" (DN80) ﬂ ange connection

2" (DN50) hose connections
from two cylinders

OM-7913

OM-7914

Notes:
• For two cylinders, connect the stainless steel tube connector directly to the dispersion inlet as shown.

The diameter and pitch of the tube connector must match the inlet diameter and pitch of the dispersion unit.

•

Always run separate steam hose/tubing from each cylinder to the connection of the dispersion device.
Only connect a maximum of two cylinders to any single dispersion unit.

FIGURE 25-1: CONNECTING TWO CYLINDERS TO A DISPERSION ASSEMBLY

WARNING

Preventing back pressure/abnormal
operation in dual cylinder humidifi ers
and installations where two individual
units are connected to a single
dispersion panel.

Read and follow all steam hose
installation instructions. Failure to
follow these instructions could result in
excessive back pressure or abnormal
operation of the unit. Severe personal
injury or damage to the unit may result.

«
...
27
28
29
30
31
...
»

Summary of Contents for XT Series





































































Reviews:

No comments

Related manuals for XT Series

Brand: Eldom Pages: 36

Brand: Sencor Pages: 8

Brand: Trotec Pages: 20

Brand: Boneco Pages: 68

Brand: ElectrIQ Pages: 27

Brand: anko Pages: 8

Brand: Goldair Pages: 5

Brand: Goldair Pages: 9

Brand: cecotec Pages: 92

Brand: Fantech Pages: 16

SelectAire Plus SP Series

Brand: Desert Aire Pages: 110

Brand: TurMix Pages: 15

Brand: Nortec Pages: 62

Brand: Pro Breeze Pages: 45

Brand: Qlima Pages: 88

Brand: Qlima Pages: 64

Brand: Zibro Pages: 44

Brand: Zibro Pages: 68

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands