manualshive.com logo in svg

Dräger Savina, Instructions For Use Manual

Share
Download
Dräger Savina Instructions For Use Manual Download Page 42

Operation

42

Calibrating

The saved calibration/zeroing values remain stored even when 
the machine is switched off.

Automatic calibration of the pressure sensors

The pressure sensors for measuring the airway pressure 
are calibrated automatically.

Automatic calibration of the flow sensor

The flow sensor will be automatically calibrated in the following 
circumstances: 

— when the apparatus is switched on
— every 24 hours during operation
— after changing the flow sensor 
— after medicament nebulisation
— after bronchial suction
— after changing the O

2

 concentration.

Savina uses a full inspiration phase for calibration. Short 
inspiration times are extended to about one second.

Message in the information line on the screen:

Flow calibration in progress

After calibration is complete, the following message appears in 
the information line:

Flow-calibration ok

If calibration is unsuccessful, the following message appears: 
"Flow-calibration failed". The expiratory part of the flow curve 
does not appear and no measured values are displayed for VTe, 
MV or PEEP.

Then

●

Exchange flow sensor.  

 

●

Always pay special attention to successful flow 
calibration. Without a usable flow measurement, 
neither O

2

 calibration nor O

2

 enrichment for bronchial 

suction is possible. 

1

0

4 3

7

388

Summary of Contents for Savina





































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands