Dräger Regard 3900 Instructions For Use Manual Download Page 48

,QVWUXFWLRQVIRUXVH

_

REGARD

®

 3900

_

Safety-related information

1 Safety-related 

information

– Before using this product, carefully read these instructions for use and those of 

the associated products.

– Strictly follow the instructions for use. The user must fully understand and strictly 

observe the instructions. Use the product only for the purposes specified in the 
intended use section of this document.

– Do not dispose of the instructions for use. Ensure that they are stored and used 

appropriately by the product user.

– Only trained and competent users are permitted to use this product.
– Do not use a faulty or incomplete product. Do not modify the product.
– Notify Dräger in the event of any component fault or failure.
– Comply with all local and national rules and regulations associated with this 

product.

– Only trained and qualified personnel are permitted to inspect, repair and service 

the product as detailed in these instructions for use (see "Maintenance", 
page 77). Further maintenance work that is not detailed in these instructions for 
use must only be carried out by Dräger or personnel qualified by Dräger. Dräger 
recommend a Dräger service contract for all maintenance activities. 

– Use only genuine Dräger spare parts and accessories. Otherwise, the proper 

functioning of the product may be impaired.

Safe coupling with electrical devices

Electrical connections to devices which are not listed in these instructions for use 
should only be made following consultation with the respective manufacturers or an 
expert.

Use in areas subject to explosion hazards

Devices or components for use in explosion-hazard areas which have been tested 
and approved according to national, European or international explosion protection 
regulations may only be used under the conditions specified in the approval and 
with consideration of the relevant legal regulations. The devices or components 
may not be modified in any manner. The use of faulty or incomplete parts is 
forbidden. The appropriate regulations must be observed at all times when carrying 
out repairs on these devices or components.

Conventions in this document

2.1 

Meaning of the warning notices

The following warning notices are used in this document to alert the user to 
potential hazards. The meanings of the warning notices are defined as follows:

Warning sign

Signal word

Classification of the warning notice

DANGER

Indicates an imminently hazardous situa-
tion. If not avoided, it will result in death or 
serious injury.

WARNING

Indicates a potentially hazardous situation. 
If not avoided, it could result in death or 
serious injury.

Summary of Contents for Regard 3900





































































































































































































































































































Reviews: