Dongfeng Sokon; C Series Repair & Maintenance Handbook Download Page 20

Page: 20 / 94

Notice:

If the car is driving on dusty road very often, clean or replace the filter every 2,500 kms.

Fuel filter

Replacement
Warning:

Keep off from fire when changing the fuel filter and in a place with good ventilation.

Fuel filter is above the fuel tank, including the fuel pump assembly.
Change fuel filter interval. Refer to chapter three for detail knock down and installment.

Fuel pipe and fuel case

Check

Check if there’s any leakage, crack, or damage of the fuel tank, fuel pipes, and
connectors, make sure that all clips are tightly fixed.

Replace the connectors when it’s leaking. Also change when there’re
cracks or damages.

．

Arrester

1. Fuel pump; 5. Drain out valve

2. Fuel pump filter; 6.Two-way single valve

3. Fuel filter; 7. Fuel disconnecting valve

4. Fuel ruler 8. Fuel pump assy

Summary of Contents for C Series































































































Search results

Summary of Contents for C Series

Reviews:

Related manuals for C Series

Brands by name

Popular brands

Dongfeng Sokon; C Series, Repair & Maintenance Handbook

Search results

Summary of Contents for C Series

Reviews:

Related manuals for C Series

Brands by name

Popular brands