Dodge 2011 Challenger Owner'S Manual Download Page 398 | Manualshive

Page: 398 / 490

background image

WARNING! (Continued)

•

The battery in this vehicle has a vent hose that
should not be disconnected and should only be
replaced with a battery of the same type (vented).

CAUTION!

•

It is essential when replacing the cables on the
battery that the positive cable is attached to the
positive post and the negative cable is attached to
the negative post. Battery posts are marked posi-
tive (+) and negative (-) and are identified on the
battery case. Cable clamps should be tight on the
terminal posts and free of corrosion.

•

If a “fast charger” is used while the battery is in
the vehicle, disconnect both vehicle battery cables
before connecting the charger to the battery. Do
not use a “fast charger” to provide starting voltage.

Air Conditioner Maintenance

For best possible performance, your air conditioner
should be checked and serviced by an authorized dealer
at the start of each warm season. This service should
include cleaning of the condenser fins and a performance
test. Drive belt tension should also be checked at this
time.

CAUTION!

Do not use chemical flushes in your air conditioning
system as the chemicals can damage your air condi-
tioning components. Such damage is not covered by
the New Vehicle Limited Warranty.

396

MAINTAINING YOUR VEHICLE

«
...
396
397
398
399
400
...
»

Summary of Contents for 2011 Challenger











































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for 2011 Challenger

Brand: ZAPTEC Pages: 64

Brand: ZAPTEC Pages: 24

Brand: Vaisala Pages: 24

Cherokee 16 1982

Brand: Jeep Pages: 1311

Brand: Roav Pages: 10

Brand: TBC Pages: 12

Brand: Prorack Pages: 14

Brand: Hama Pages: 4

Brand: Volvo Pages: 230

Brand: Axxess Pages: 8

Brand: Dodge Pages: 276

GMC Yukon Denali 2005

Brand: Cadillac Pages: 456

Brand: Saab Pages: 63

Brand: R&G Pages: 20

Brand: Whispbar Pages: 70

Brand: Fab Fours Pages: 21

Brand: TAUBENREUTHER Pages: 18

Jumpy Miltispace

Brand: CITROËN Pages: 164

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands